AK4673 Datasheet, PDF (5/107 Pages) Asahi Kasei Microsystems – Stereo CODEC with MIC/HP-AMP and Touch Screen Controller

[AK4673]
PIN/FUNCTION
No. Pin Name
A1 NC
C2 MPWR
A2 VCOM
B1 VSS1
C1 AVDD
E2 ^VCOC
RIN3
F2 NC
D2 I2CA
G2 PDN
H1 CADA
H2 SCLA
J1 NC
J2 SDAA
H3 SDTI
J3 SDTO
H4 LRCK
J4 BICK
H5 NC
J6 DVDD
H7 NC
H6 TVDD2
J7 TVDD1
J8 NC
H9 MCKI
G8 NC
G9 NC
H8 MCKO
J9 NC
D8 VSS2
D9 HVDD
C8 HPR
C9 HPL
B8 NC
B9 MUTET
I/O
Function
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
O MIC Power Supply Pin
O
Common Voltage Output Pin, 0.45 x AVDD
Bias voltage of ADC inputs and DAC outputs.
- Ground 1 Pin
- Analog Power Supply Pin, 2.6 ~ 3.6V
O
Output Pin for Loop Filter of PLL Circuit (AIN3 bit = “0”: PLL is available.)
This pin should be connected to VSS1 with one resistor and capacitor in series.
I Rch Analog Input 3 Pin (AIN3 bit = “1”: PLL is not available.)
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
I I²C Control Mode Pin. This pin should be tied to AVDD.
Power-Down Mode Pin (This pin is valid only for the Audio Block)
I
“H”: Power-up, “L”: Power-down
This pin does not apply to a power down and a reset for the TSC block and TSC related
registers. Power-down on the TSC block is determined by the PD0 bit shown in Table 61.
I Audio Block I²C bus Slave Address (CADA) bit Select Pin
I Audio Block Control Data Clock Pin.
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
I/O Audio Block Control Data Input Pin.
I Audio Serial Data Input Pin
O Audio Serial Data Output Pin
I/O Input / Output Channel Clock Pin
I/O Audio Serial Data Clock Pin
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
- Digital Power Supply Pin, 2.6 ~ 3.6V
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
- Digital I/O Power Supply Pin (Audio Stream), 1.6 ~ 3.6V
-
Digital I/O Power Supply Pin (uP I/F), 2.5 ~ 3.6V
This pin should be connected to TSVDD pin.
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
I External Master Clock Input Pin
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
O Master Clock Output Pin
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
- Ground 2 Pin
- Headphone Amp Power Supply Pin, 2.6 ~ 5.25V
O Rch Headphone-Amp Output Pin
O Lch Headphone-Amp Output Pin
-
No Connection pin
No internal bonding. This pin should be connected to ground (VSS1, VSS2 or VSS3 pin).
O
Mute Time Constant Control Pin
Connected to VSS2 pin with a capacitor for mute time constant.
MS0670-E-00
-5-
2007/09