HD3SS3220_15 Datasheet, PDF (5/43 Pages) Texas Instruments – HD3SS3220 USB Type-C DRP Port Controller with SuperSpeed 2:1 MUX

www.ti.com
HD3SS3220
SLLSES1 – DECEMBER 2015
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)⁽¹⁾
5-V Supply Voltage
3.3-V Supply Voltage
Control Pins
Super-speed Differential Signal Pins
Storage temperature, T_stg
VDD5
VCC33
CC1, CC2, ADDR, PORT, ID, DIR,
INT_N/OUT3, ENn_CC, ENn_MUX,
SDA/OUT1, SCL/OUT2
ENn_MUX, DIR
VBUS_DET
[RX/TX] [p/n], [RX/TX][2/1][p/n]
MIN
MAX
UNIT
–0.3
6
V
–0.3
4
V
–0.3
VDD5 +0.3
V
–0.3
VCC33 +0.3
V
–0.3
4
V
–0.3
2.5
V
–65
150
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
V_(ESD) Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001⁽¹⁾
Charged-device model (CDM), per JEDEC specification JESD22-
C101 ⁽²⁾
VALUE
±2000
±1500
UNIT
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions. Pins listed as ±XXX V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process..
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
V_DD
V_(diff)
V_(cm)
T_A
T_A
V_(BUS)
C_(BULK)
R_{(p_ODext)}
R_{(p_TLext)}
R_{(p_15A)}
R_{(p_3A)}
R_{(p_i2c_ext)}
R_(VBUS)
C_(bus,I2c)
5-V Supply Voltage range
3.3-V Supply Voltage range
Supply range for I2C (SDA, SCL) pins
High speed signal pins differential voltage
High speed signal pins common mode voltage
Operating free-air/ambient temperature (HD3SS3220)
Operating free-air/ambient temperature (HD3SS3220I)
System V_(BUS) input voltage through 900-K resistor
Bulk capacitance on VCONN. Only when VCONN is on.
Disconnected when VCONN is off. Shall be placed on VDD5.
External Pull up resistor on Open Drain IOs (OUT1, OUT2,
INT/OUT3, ID, VCONN_FAULT_N, and DIR pins)
Tri-level input external pull-up resistor (PORT and ADDR pins)
External pull up resistor to advertise 1.5 A (CURRENT_MODE pin)
External pull up resistor to advertise 3 A (CURRENT_MODE pin)
External Pull up resistance on I²C bus
(Could be 4.7 K or higher. Nominal value listed)
External resistor on VBUS_DET pin
Total capacitive load for each I²C bus line
MIN
4.5 ⁽¹⁾
3
1.65
0
0
0
–40
4
10
890
(1) With 200 mA VCONN current for VCONN ≥ 4.75 V at connector, VDD5 ≥ 5 V is recommended
NOM
5
200
4.7
500
10
2.2
900
MAX
5.5
3.6
3.6
1.8
2
70
85
28
200
910
400
UNIT
V
V
V
V_PP
V
°C
°C
V
µF
KΩ
KΩ
KΩ
KΩ
KΩ
KΩ
pF
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: HD3SS3220
Submit Documentation Feedback
5