English
Language : 

MC68HC705C8A Datasheet, PDF (174/222 Pages) Motorola, Inc – HCMOS Microcontroller Unit
◁
Electrical Specifications
13.8 3.3-Volt DC Electrical Characteristics
Characteristic(1)
Symbol
Min
Typ(2)
Max
Unit
Output voltage, ILoad ≤ 10.0 µA
Output high voltage
ILoad = –0.2 mA
PA7–PA0, PB7–PB0, PC6–PC0, TCMP
(see Figure 13-2)
ILoad = –0.4 mA
PD4–PD1 (see Figure 13-3)
ILoad = –1.5 mA
PC7
VOL
—
—
VOH
VDD – 0.1
—
0.1
—
V
VOH
VDD – 0.3
—
—
—
—
V
—
—
Output low voltage (see Figure 13-4)
ILoad = 0.4 mA
PA7–PA0, PB7–PB0, PC6–PC0, PD4–PD1
ILoad = 6.0 mA
PC7
VOL
—
—
0.3
V
—
—
0.3
Input high voltage
PA7–PA0, PB7–PB0, PC7–PC0, PD5–PD0,
PD7, TCAP, IRQ, RESET, OSC1
VIH
0.7 x VDD
—
VDD
V
Input low voltage
PA7–PA0, PB7–PB0, PC7–PC0, PD5–PD0,
PD7, TCAP, IRQ, RESET, OSCI
VIL
VSS
—
0.2 x VDD V
Data-retention mode (0°C to 70°C)
VRM
2.0
—
—
V
Supply current(3)
Run(4)
Wait(5)
Stop(6)
IDD
—
1.53
3.0
mA
—
0.711
1.0
mA
—
2.0
20
µA
I/O ports hi-z leakage current
PA7–PA0, PB7–PB0, PC7–PC0, PD4–PD1,
PD7, RESET
IIL
—
—
± 10
µA
Input current
IRQ, TCAP, OSC1, PD5, PD0
IIn
—
—
±1
µA
1. VDD = 3.3 V ± 10%; VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
2. Typical values at midpoint of voltage range, 25°C only.
3. IDD measured with port B pullup devices disabled.
4. Run (operating) IDD measured using external square wave clock source (fOSC = 2.0 MHz). All inputs 0.2 V from rail. No dc
loads. Less than 50 pF on all outputs. CL = 20 pF on OSC2. OSC2 capacitance linearly affects run IDD.
5. Wait IDD measured using external square wave clock source (fOSC = 2.0 MHz). All inputs 0.2 V from rail. No dc loads. Less
than 50 pF on all outputs. CL = 20 pF on OSC2. VIL = 0.2 V, VIH = VDD – 0.2 V. All ports configured as inputs. SPI and SCI
disabled. If SPI and SCI enabled, add 10% current draw. OSC2 capacitance linearly affects wait IDD.
6. Stop IDD measured with OSC1 = VDD. All ports configured as inputs. VIL = 0.2 V; VIH = VDD – 0.2 V.
Technical Data
174
Electrical Specifications
MC68HC705C8A — Rev. 2.0
MOTOROLA
 ▷