PIC16F1933_11 Datasheet, PDF (98/430 Pages) Microchip Technology – 28-Pin Flash-Based, 8-Bit CMOS Microcontrollers LCD Driver and nanoWatt XLP Technology

PIC16(L)F1933
9.1.1 WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If the interrupt occurs before the execution of a
SLEEP instruction
- SLEEP instruction will execute as a NOP.
- WDT and WDT prescaler will not be cleared
- TO bit of the STATUS register will not be set
- PD bit of the STATUS register will not be
cleared.
• If the interrupt occurs during or after the execu-
tion of a SLEEP instruction
- SLEEP instruction will be completely exe-
cuted
- Device will immediately wake-up from Sleep
- WDT and WDT prescaler will be cleared
- TO bit of the STATUS register will be set
- PD bit of the STATUS register will be cleared.
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
FIGURE 9-1:
WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
OSC1⁽¹⁾
CLKOUT⁽²⁾
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
TOST⁽³⁾
Interrupt flag
GIE bit
(INTCON reg.)
Instruction Flow
PC
PC
Instruction
Fetched
Inst(PC) = Sleep
Instruction
Executed
Inst(PC - 1)
Processor in
Sleep
PC + 1
Inst(PC + 1)
Sleep
PC + 2
Interrupt Latency⁽⁴⁾
PC + 2
Inst(PC + 2)
Inst(PC + 1)
PC + 2
Dummy Cycle
0004h
Inst(0004h)
Dummy Cycle
0005h
Inst(0005h)
Inst(0004h)
Note 1:
2:
3:
4:
XT, HS or LP Oscillator mode assumed.
CLKOUT is not available in XT, HS or LP Oscillator modes, but shown here for timing reference.
TOST = 1024 TOSC (drawing not to scale). This delay applies only to XT, HS or LP Oscillator modes.
GIE = 1 assumed. In this case after wake-up, the processor calls the ISR at 0004h. If GIE = 0, execution will continue in-line.
TABLE 9-1: SUMMARY OF REGISTERS ASSOCIATED WITH POWER-DOWN MODE
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
INTCON
GIE
PEIE
TMR0IE
INTE
IOCIE
TMR0IF
INTF
IOCIF
IOCBF
IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0
IOCBN
IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0
IOCBP
IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0
PIE1
TMR1GIE ADIE
RCIE
TXIE
SSPIE CCP1IE TMR2IE TMR1IE
PIE2
OSFIE
C2IE
C1IE
EEIE
BCLIE
LCDIE
—
CCP2IE
PIE3
—
CCP5IE CCP4IE CCP3IE TMR6IE
—
TMR4IE
—
PIR1
TMR1GIF ADIF
RCIF
TXIF
SSPIF CCP1IF TMR2IF TMR1IF
PIR2
OSFIF
C2IF
C1IF
EEIF
BCLIF
LCDIF
—
CCP2IF
PIR3
—
CCP5IF CCP4IF CCP3IF TMR6IF
—
TMR4IF
—
STATUS
—
—
—
TO
PD
Z
DC
C
WDTCON
—
—
WDTPS<4:0>
SWDTEN
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used in Power-Down mode.
Register on
Page
86
134
134
134
87
88
89
90
91
92
22
101
DS41575A-page 98
Preliminary
 2011 Microchip Technology Inc.