PIC16F1933_11 Datasheet, PDF (376/430 Pages) Microchip Technology – 28-Pin Flash-Based, 8-Bit CMOS Microcontrollers LCD Driver and nanoWatt XLP Technology

PIC16(L)F1933
30.3 DC Characteristics: PIC16(L)F1933-I/E (Power-Down) (Continued)
PIC16LF1933
PIC16F1933
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD)⁽²⁾
D028
—
0.1
1
—
0.1
2
7
A
1.8 A/D Current (Note 1, Note 3), no
8
A
3.0 ^{conversion in progress}
D028
—
16
56
—
21
58
70
A
1.8 A/D Current (Note 1, Note 3), no
73
A
3.0 ^{conversion in progress}
—
25
61
76
A
5.0
D029
—
250
—
—
250
—
—
A
1.8 A/D Current (Note 1, Note 3),
—
A
3.0 ^{conversion in progress}
D029
—
280
—
—
280
—
—
A
1.8 A/D Current (Note 1, Note 3,
—
A
3.0 ^{Note 4), conversion in progress}
—
280
—
—
A
5.0
D030
—
3.5
6
6
A
1.8 Cap Sense, Low-Power mode
—
7
9
9
A
3.0
D030
—
17
61
76
A
1.8 Cap Sense, Low-Power mode
—
21
64
79
A
3.0
—
22
66
83
A
5.0
D031
—
1
—
—
A
3.0 LCD Bias Ladder, Low-power
—
10
—
—
A
3.0 LCD Bias Ladder, Medium-power
—
75
—
—
A
3.0 LCD Bias Ladder, High-power
D031
—
1
—
—
A
5.0 LCD Bias Ladder, Low-power
—
10
—
—
A
5.0 LCD Bias Ladder, Medium-power
—
75
—
—
A
5.0 LCD Bias Ladder, High-power
D032
—
7.6
18
18
A
1.8 Comparator, Low Power mode
—
8.0
20
20
A
3.0
D032
—
24
65
81
A
1.8 Comparator, Low Power mode
—
26
75
94
A
3.0
—
28
76
95
A
5.0
*
†
Legend:
Note 1:
2:
3:
4:
These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
TBD = To Be Determined
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
A/D oscillator source is FRC.
0.1 F capacitor on VCAP (RA0).
DS41575A-page 376
Preliminary
 2011 Microchip Technology Inc.