RFPIC12F675 Datasheet, PDF (67/136 Pages) Microchip Technology – FLASH-Based Microcontroller with ASK/FSK Transmitter

rfPIC12F675
10.4.1 GP2/INT INTERRUPT
External interrupt on GP2/INT pin is edge-triggered;
either rising if INTEDG bit (OPTION<6>) is set, of
falling, if INTEDG bit is clear. When a valid edge
appears on the GP2/INT pin, the INTF bit
(INTCON<1>) is set. This interrupt can be disabled by
clearing the INTE control bit (INTCON<4>). The INTF
bit must be cleared in software in the Interrupt Service
Routine before re-enabling this interrupt. The GP2/INT
interrupt can wake-up the processor from SLEEP if the
INTE bit was set prior to going into SLEEP. The status
of the GIE bit decides whether or not the processor
branches to the interrupt vector following wake-up. See
Section 10.9 for details on SLEEP and Figure 10-13 for
timing of wake-up from SLEEP through GP2/INT
interrupt.
Note:
The ANSEL (9Fh) and CMCON (19h)
registers must be initialized to configure an
analog channel as a digital input. Pins
configured as analog inputs will read ‘0’.
10.4.2 TMR0 INTERRUPT
An overflow (FFh  00h) in the TMR0 register will
set the T0IF (INTCON<2>) bit. The interrupt can
be enabled/disabled by setting/clearing T0IE
(INTCON<5>) bit. For operation of the Timer0 module,
see Section 4.0.
10.4.3 GPIO INTERRUPT
An input change on GPIO change sets the GPIF
(INTCON<0>) bit. The interrupt can be enabled/
disabled by setting/clearing the GPIE (INTCON<3>)
bit. Plus individual pins can be configured through the
IOC register.
Note:
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the GPIF inter-
rupt flag may not get set.
10.4.4 COMPARATOR INTERRUPT
See Section 6.9 for description of comparator interrupt.
10.4.5 A/D CONVERTER INTERRUPT
After a conversion is complete, the ADIF flag (PIR<6>)
is set. The interrupt can be enabled/disabled by setting
or clearing ADIE (PIE<6>).
See Section 7.0 for operation of the A/D converter
interrupt.
FIGURE 10-11: INT PIN INTERRUPT TIMING
OSC1
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
CLKOUT 3
4
INT pin
1
INTF Flag
(INTCON<1>)
1
5
GIE bit
(INTCON<7>)
Interrupt Latency ₂
INSTRUCTION FLOW
PC
PC
Instruction
Fetched
Inst (PC)
PC+1
Inst (PC+1)
PC+1
—
0004h
Inst (0004h)
0005h
Inst (0005h)
Instruction
Executed
Inst (PC-1)
Inst (PC)
Dummy Cycle
Dummy Cycle
Inst (0004h)
Note 1: INTF flag is sampled here (every Q1).
2: Asynchronous interrupt latency = 3-4 TCY. Synchronous latency = 3 TCY, where TCY = instruction cycle time. Latency
is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3: CLKOUT is available only in RC Oscillator mode.
4: For minimum width of INT pulse, refer to AC specs.
5: INTF is enabled to be set any time during the Q4-Q1 cycles.
 2003-2013 Microchip Technology Inc.
Preliminary
DS70091B-page 67