PIC18F66K22-I Datasheet, PDF (489/550 Pages) Microchip Technology – PIC18F87K22 Family Data Sheet

PIC18F87K22 FAMILY
31.2 DC Characteristics: Power-Down and Supply Current
PIC18F87K22 Family (Industrial/Extended) (Continued)
PIC18F87K22 Family
(Industrial/Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Typ
Max Units
Conditions
Note
Supply Current (IDD)^(2,3)
All devices 5.3
10 µA
-40°C
5.5
10 µA
5.5
10 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
12
24 µA
+125ºC
All devices 10
10
11
15
15 µA
16 µA
17 µA
35 µA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 31 kHz
(RC_RUN mode,
LF-INTOSC)
All devices 70
180 µA
-40°C
80
185 µA
90
190 µA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
200
500 µA
+125ºC
All devices 410
850 µA
-40°C
410
800 µA
410
830 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
700
1500 µA
+125ºC
All devices 680
680
670
800
990 µA
960 µA
950 µA
1700 µA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 1 MHz
(RC_RUN mode,
HF-INTOSC)
All devices 760
1400 µA
-40°C
780
1400 µA
800
1500 µA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
1200 2400 µA
+125ºC
All devices 760
1300 µA
-40°C
760
1400 µA
770
1500 µA
+25°C
+85°C
VDD = 1.8V⁽⁴⁾
Regulator Disabled
800
1700 µA
+125ºC
All devices 1.4
1.4
1.4
1.5
2.5 mA
2.5 mA
2.5 mA
3.0 mA
-40°C
+25°C
+85°C
+125ºC
VDD = 3.3V⁽⁴⁾
Regulator Disabled
FOSC = 4 MHz
(RC_RUN mode,
HF-INTOSC)
All devices 1.5
2.7 mA
-40°C
1.5
2.7 mA
1.5
2.7 mA
+25°C
+85°C
VDD = 5V⁽⁵⁾
Regulator Enabled
1.6
3.3 mA
+125ºC
1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta
current are disabled (such as WDT, SOSC oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
The test conditions for all IDD measurements in Active Operation mode are:
OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;
MCLR = VDD; WDT enabled/disabled as specified.
3: Standard, low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature
crystals are available at a much higher cost.
4: Voltage regulator disabled (ENVREG = 0, tied to VSS, RETEN (CONFIG1L<0>) = 1).
5: Voltage regulator enabled (ENVREG = 1, tied to VDD, SRETEN (WDTCON<4>) = 1 and RETEN (CONFIG1L<0>) = 0).
6: 48 MHz, maximum frequency at +125ºC.
 2011 Microchip Technology Inc.
DS39960D-page 489