PIC16F1938_13 Datasheet, PDF (386/488 Pages) Microchip Technology – 28/40/44-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver

PIC16(L)F1938/9
30.3 DC Characteristics: PIC16(L)F1938/39-I/E (Power-Down) (Continued)
PIC16LF1938/39
PIC16F1938/39
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
D028
D028
D028A
D028A
D029*
D029*
D030
D030
D031
D031
Device Characteristics Min.
Power-down Base Current (IPD)⁽²⁾
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Typ†
0.1
0.1
16
21
25
250
250
280
280
280
3.5
7.0
17
21
22
1
10
75
1
10
75
7.6
8.0
24
26
Max.
+85°C
Max.
+125°C
Units
5.0
8.0
A
6.0
9.0
A
35
45
A
40
50
A
50
60
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
—
—
A
22
25
A
23
27
A
50
60
A
70
80
A
Conditions
VDD
Note
1.8 A/D Current (Note 1, Note 3), no
3.0 ^{conversion in progress}
1.8 A/D Current (Note 1, Note 3), no
3.0 ^{conversion in progress}
5.0
1.8 A/D Current (Note 1, Note 3),
3.0 ^{conversion in progress}
1.8 A/D Current (Note 1, Note 3),
3.0 ^{conversion in progress}
5.0
1.8 Cap Sense, Low-Power mode
3.0
1.8 Cap Sense, Low-Power mode
3.0
5.0
3.0 LCD Bias Ladder, Low power
3.0 LCD Bias Ladder, Medium power
3.0 LCD Bias Ladder, High power
5.0 LCD Bias Ladder, Low power
5.0 LCD Bias Ladder, Medium power
5.0 LCD Bias Ladder, High power
1.8 Comparator, Low-Power mode
3.0
1.8 Comparator, Low-Power mode
3.0
—
28
75
85
A
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1:
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
4: 0.1 F capacitor on VCAP (RA0).
DS40001574C-page 386
 2011-2013 Microchip Technology Inc.