|
PIC16F1938_13 Datasheet, PDF (384/488 Pages) Microchip Technology – 28/40/44-Pin Flash-Based, 8-Bit CMOS Microcontrollers with LCD Driver | |||
|
◁ |
PIC16(L)F1938/9
30.2 DC Characteristics: PIC16F/LF1938/39-I/E (Industrial, Extended) (Continued)
PIC16LF1938/9
PIC16F1938/9
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ï£ TA ï£ +85°C for industrial
-40°C ï£ TA ï£ +125°C for extended
Param
No.
Device
Characteristics
Min. Typâ Max. Units
VDD
Conditions
Note
Supply Current (IDD)(1, 2)
D017
â
90
160
ïA
â
120
190
ïA
D017
â
120
190
ïA
â
150
240
ïA
â
190
320
ïA
D018
â
0.6
0.8
mA
â
1.0
1.3
mA
1.8 FOSC = 500 kHz
3.0 MFINTOSC mode
1.8 FOSC = 500 kHz
3.0 MFINTOSC mode (Note 5)
5.0
1.8 FOSC = 8 MHz
3.0 HFINTOSC mode
D018
D019
D019
D020
D020
D021
D021
D022
â
0.7
0.9
mA
â
1.0
1.4
mA
â
1.2
1.5
mA
â
1.0
1.2
mA
â
1.6
2.0
mA
â
1.0
1.3
mA
â
1.6
2.0
mA
â
1.8
2.2
mA
â
3.0
3.9
mA
â
3.7
4.6
mA
â
3.0
3.9
mA
â
3.3
4.1
mA
â
200
300
ïA
â
350
490
ïA
â
210
300
ïA
â
370
500
ïA
â
460
590
ïA
â
3.0
3.9
mA
â
3.7
4.6
mA
1.8 FOSC = 8 MHz
3.0 HFINTOSC mode (Note 5)
5.0
1.8 FOSC = 16 MHz
3.0 HFINTOSC mode
1.8 FOSC = 16 MHz
3.0 HFINTOSC mode (Note 5)
5.0
3.0 FOSC = 32 MHz
3.6 HFINTOSC mode
3.0 FOSC = 32 MHz
5.0 HFINTOSC mode
1.8 FOSC = 4 MHz
3.0 EXTRC mode (Note 3)
1.8 FOSC = 4 MHz
3.0 EXTRC mode (Note 3, Note 5)
5.0
3.0 FOSC = 32 MHz
3.6 HS Oscillator mode (Note 6)
D022
Note 1:
2:
3:
4:
5:
6:
â
3.0
3.9
mA
3.0 FOSC = 32 MHz
â
3.3
4.1
mA
5.0 HS Oscillator mode (Note 5, Note 6)
The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in kïï®
FVR and BOR are disabled.
0.1 ïF capacitor on VCAP (RA0).
8 MHz crystal oscillator with 4x PLL enabled.
DS40001574C-page 384
ï£ 2011-2013 Microchip Technology Inc.
|
▷ |