|
PIC16F610 Datasheet, PDF (3/180 Pages) Microchip Technology – 14-Pin, Flash-Based 8-Bit CMOS Microcontrollers | |||
|
◁ |
PIC16F610/616/16HV610/616
14-Pin Flash-Based, 8-Bit CMOS Microcontrollers
High-Performance RISC CPU:
⢠Only 35 instructions to learn:
- All single-cycle instructions except branches
⢠Operating speed:
- DC â 20 MHz oscillator/clock input
- DC â 200 ns instruction cycle
⢠Interrupt capability
⢠8-level deep hardware stack
⢠Direct, Indirect and Relative Addressing modes
Special Microcontroller Features:
⢠Precision Internal Oscillator:
- Factory calibrated to ±1%, typical
- User selectable frequency: 4 MHz or 8 MHz
⢠Power-Saving Sleep mode
⢠Voltage range:
- PIC16F610/616: 2.0V to 5.5V
- PIC16HV610/616: 2.0V to user defined
maximum (see note)
⢠Industrial and Extended Temperature range
⢠Power-on Reset (POR)
⢠Power-up Timer (PWRT) and Oscillator Start-up
Timer (OST)
⢠Brown-out Reset (BOR)
⢠Watchdog Timer (WDT) with independent
oscillator for reliable operation
⢠Multiplexed Master Clear with pull-up/input pin
⢠Programmable code protection
⢠High Endurance Flash:
- 100,000 write Flash endurance
- Flash retention: > 40 years
Low-Power Features:
⢠Standby Current:
- 50 nA @ 2.0V, typical
⢠Operating Current:
- 20 μA @ 32 kHz, 2.0V, typical
- 220 μA @ 4 MHz, 2.0V, typical
⢠Watchdog Timer Current:
- 1 μA @ 2.0V, typical
Note: Voltage across internal shunt regulator
cannot exceed 5V.
Peripheral Features:
⢠Shunt Voltage Regulator (PIC16HV610/616 only):
- 5 volt regulation
- 4 mA to 50 mA shunt range
⢠11 I/O pins and 1 input only
- High current source/sink for direct LED drive
- Interrupt-on-Change pins
- Individually programmable weak pull-ups
⢠Analog Comparator module with:
- Two analog comparators
- Programmable on-chip voltage reference
(CVREF) module (% of VDD)
- Fixed Voltage Reference
- Comparator inputs and outputs externally
accessible
- SR Latch
- Built-In Hysteresis (user selectable)
⢠Timer0: 8-bit timer/counter with 8-bit
programmable prescaler
⢠Enhanced Timer1:
- 16-bit timer/counter with prescaler
- External Timer1 Gate (count enable)
- Option to use OSC1 and OSC2 in LP mode
as Timer1 oscillator if INTOSC mode
selected
- Timer1 oscillator
⢠In-Circuit Serial ProgrammingTM (ICSPTM) via two
pins
PIC16F616/16HV616 only:
⢠A/D Converter:
- 10-bit resolution
- 8 external input channels
- 2 internal reference channels
⢠Timer2: 8-bit timer/counter with 8-bit period
register, prescaler and postscaler
⢠Enhanced Capture, Compare, PWM module:
- 16-bit Capture, max. resolution 12.5 ns
- 16-bit Compare, max. resolution 200 ns
- 10-bit PWM with 1, 2 or 4 output channels,
programmable âdead timeâ, max. frequency
20 kHz
© 2007 Microchip Technology Inc.
Preliminary
DS41288C-page 1
|
▷ |