|
PIC17C44 Datasheet, PDF (177/241 Pages) Microchip Technology – High-Performance 8-Bit CMOS EPROM/ROM Microcontroller | |||
|
◁ |
PIC17C4X
Applicable Devices 42 R42 42A 43 R43 44
19.1 DC CHARACTERISTICS:
PIC17CR42/42A/43/R43/44-16 (Commercial, Industrial)
PIC17CR42/42A/43/R43/44-25 (Commercial, Industrial)
PIC17CR42/42A/43/R43/44-33 (Commercial, Industrial)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40ËC ⤠TA ⤠+85ËC for industrial and
0ËC ⤠TA ⤠+70ËC for commercial
Parameter
No.
Sym
Characteristic
Min Typâ Max Units
Conditions
D001
VDD Supply Voltage
4.5
â 6.0
V
D002
VDR RAM Data Retention 1.5 * â
â
Voltage (Note 1)
V Device in SLEEP mode
D003
VPOR VDD start voltage to
â
ensure internal
Power-on Reset signal
VSS â
V See section on Power-on Reset for
details
D004
SVDD VDD rise rate to
0.060 * â
ensure internal
Power-on Reset signal
â mV/ms See section on Power-on Reset for
details
D010
D011
D012
D013
D015
D014
IDD Supply Current
(Note 2)
â
3
6
mA FOSC = 4 MHz (Note 4)
â
6 12 * mA FOSC = 8 MHz
â
11 24 * mA FOSC = 16 MHz
â
19 38 mA FOSC = 25 MHz
â
25 50 mA FOSC = 33 MHz
â
95 150 µA FOSC = 32 kHz,
WDT enabled (EC osc conï¬guration)
D020
D021
IPD Power-down
Current (Note 3)
â
10 40 µA VDD = 5.5V, WDT enabled
â
<1 5
µA VDD = 5.5V, WDT disabled
*
These parameters are characterized but not tested.
â Data in "Typ" column is at 5V, 25ËC unless otherwise stated. These parameters are for design guidance only
and are not tested.
Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD or VSS, T0CKI = VDD,
MCLR = VDD; WDT enabled/disabled as speciï¬ed.
Current consumed from the oscillator and I/Oâs driving external capacitive or resistive loads needs to be con-
sidered.
For the RC oscillator, the current through the external pull-up resistor (R) can be estimated as: VDD / (2 ⢠R).
For capacitive loads, the current can be estimated (for an individual I/O pin) as (CL ⢠VDD) ⢠f
CL = Total capacitive load on the I/O pin; f = average frequency the I/O pin switches.
The capacitive currents are most signiï¬cant when the device is conï¬gured for external execution (includes
extended microcontroller mode).
3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc conï¬guration, current through Rext is not included. The current through the resistor can be esti-
mated by the formula IR = VDD/2Rext (mA) with Rext in kOhm.
© 1996 Microchip Technology Inc.
DS30412C-page 177
|
▷ |