PIC16F627A_05 Datasheet, PDF (142/180 Pages) Microchip Technology – Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology

PIC16F627A/628A/648A
17.4 DC Characteristics: PIC16F627A/628A/648A (Industrial, Extended)
PIC16LF627A/628A/648A (Industrial)
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial and
-40°C ≤ TA ≤ +125°C for extended
Operating voltage VDD range as described in DC specification Table 17-2 and
Table 17-3
Param.
No.
Sym
Characteristic/Device
Min
Typ† Max Unit
Conditions
VIL Input Low Voltage
D030
D031
D032
D033
I/O ports
with TTL buffer
VSS
—
0.8
V VDD = 4.5V to 5.5V
VSS
— 0.15 VDD V otherwise
with Schmitt Trigger input⁽⁴⁾
VSS
— 0.2 VDD V
MCLR, RA4/T0CKI,OSC1
VSS
— 0.2 VDD V (Note1)
(in RC mode)
OSC1 (in HS)
VSS
— 0.3 VDD V
OSC1 (in LP and XT)
VSS
—
0.6
V
VIH Input High Voltage
D040
D041
D042
D043
D043A
D043B
I/O ports
with TTL buffer
2.0V
—
VDD
V VDD = 4.5V to 5.5V
.25 VDD + 0.8V —
VDD
V otherwise
with Schmitt Trigger input⁽⁴⁾
0.8 VDD
—
VDD
V
MCLR RA4/T0CKI
0.8 VDD
—
VDD
V
OSC1 (XT and LP)
1.3
—
VDD
V
OSC1 (in RC mode)
0.9 VDD
—
VDD
V (Note1)
OSC1 (in HS mode)
0.7 VDD
VDD
V
D070
IPURB
IIL
PORTB weak pull-up
current
Input Leakage Current^{(2), (3)}
50
200 400
μA VDD = 5.0V, VPIN = VSS
D060
D061
D063
I/O ports (Except PORTA)
PORTA⁽⁴⁾
RA4/T0CKI
OSC1, MCLR
—
—
±1.0
μA VSS ≤ VPIN ≤ VDD, pin at high-impedance
—
—
±0.5
μA VSS ≤ VPIN ≤ VDD, pin at high-impedance
—
—
±1.0
μA VSS ≤ VPIN ≤ VDD
—
—
±5.0
μA VSS ≤ VPIN ≤ VDD, XT, HS and LP
oscillator configuration
VOL Output Low Voltage
D080
D090
I/O ports⁽⁴⁾
VOH Output High Voltage⁽³⁾
I/O ports (Except RA4⁽⁴⁾ )
—
—
0.6
V IOL = 8.5 mA, VDD = 4.5 V, -40° to +85°C
—
—
0.6
V IOL = 7.0 mA, VDD = 4.5 V, +85° to
+125°C
VDD – 0.7
—
—
V IOH = -3.0 mA, VDD = 4.5 V, -40° to +85°C
VDD – 0.7
—
—
V IOH = -2.5 mA, VDD = 4.5 V, +85° to
+125°C
D150
VOD Open-Drain High Voltage
—
—
8.5*
V RA4 pin PIC16F627A/628A/648A,
PIC16LF627A/628A/648A
Capacitive Loading Specs on Output Pins
D100* COSC2 OSC2 pin
—
D101*
CIO All I/O pins/OSC2 (in RC mode)
—
—
15
pF In XT, HS and LP modes when external
clock used to drive OSC1.
—
50
pF
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested.
Note 1: In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. It is not recommended that the PIC16F627A/628A/648A
be driven with external clock in RC mode.
2: The leakage current on the MCLR pin is strongly dependent on applied voltage level. The specified levels represent normal
operating conditions. Higher leakage current may be measured at different input voltages.
3: Negative current is defined as coming out of the pin.
4: Includes OSC1 and OSC2 when configured as I/O pins, CLKIN or CLKOUT.
DS40044D-page 140
© 2005 Microchip Technology Inc.