E3A-MA3A-H11 Datasheet, PDF (26/48 Pages) Magnetrol International, Inc. – Digital E3 Modulevel with HART® and PACTware™ Communications Liquid Level Displacer Transmitter

2.7.4 HART Menu (E3 Modulevel)
1 Device Setup
2 Level
3 % Range
4 Loop
1 Calibration
2 Basic Setup
3 Advanced Setup
4 Diagnostics
5 Review
** measurement type Interface only
26
1 Level Units
2 Process SG
3 Operating Temp
4 Set Point Calib
5 Level Offset
6 Damping
7 System Fault State
8 Trim Level (or SG)
9 Date/Time/Initials
1 Tag
2 Descriptor
3 Date
4 Message
5 Poll Address
6 Final asmbly num
1 Trim Loop Current
2 Enter Password
3 Measurement Type
4 Model Parameters
** Interface Parameters
5 Calibration Selected
IF FACTORY SELECTED:
6 Factory Settings
7 New User Password
IF USER SELECTED:
6 User Wet Calib
7 Factory Settings
8 New User Password
1 Loop Test
2 LVDT %
3 Channel 0
4 Channel 1
5 Adj Sensor Cal Lo
6 Adj Sensor Cal Hi
7 Conversion Factor
8 Scale Offset
9 Present Status
10 Status History
11 Temp Information
1 Model
2 Manufacturer
3 Magnetrol S/N
4 Firmware Version
5 Tag
6 Descriptor
7 Date
8 Message
9 Poll Address
10 Final asmbly num
11 Device ID
12 PV is
13 Level Units
1 Capture Values
2 Enter Values
1 4mA
2 20mA
3 20mA by %
4 End
1 4mA Set Point
2 20mA Set Point
1 Model Number
2 Spring SG Range
3 Spring Rate
4 Temperature Limit
5 Displacer Length
6 Displacer Diameter
7 Displacer Weight
1 Lower SG
2 Upper SG
1 Magnetrol SN
2 Device ID
3 Factory Cal Params
4 NSP Value
5 Factory Param 1
6 Factory Param 2
1 Set Dry Point
2 Set Low Calib Pts
3 Set High Calib Pts
4 LVDT %
5 Dry Sensor Value
6 Sensor Cal Lo
7 Level (or SG) Cal Lo
8 Sensor Cal Hi
9 Level (or SG) Cal Hi
1 Faults
2 Warnings
1 View History
2 Reset History
1 Elec Temperature
2 Max Temperature
3 Min Temperature
4 Reset Temperature
1 Set Dry Point
2 Set Low Calib Pts
3 Set High Calib Pts
4 LVDT %
5 Calib SG
6 Dry Sensor Value
7 Sensor Cal Lo
8 Level (or SG) Cal Lo
9 Sensor Cal Hi
10 Level (or SG) Cal Hi
1 Default Params
2 Loop Failure
3 Primary Fault
4 Core Drop
5 Secondary Fault Hi
6 Secondary Fault Lo
1 Calib required
2 Trim Required
3 Hi Temperature
4 Lo Temperature
5 Cal Span Warning
6 Initializing
14 Level Offset
15 Process SG
16 Operating Temp
17 4mA Set Point
18 20mA Set Point
19 Damping
20 System Fault State
21 Trim Level (or SG)
22 4mA Trim Value
23 20mA Trim Value
24 Measurement Type
25 Calibration Selected
26 Model Number
27 Spring SG Range
28 Spring Rate
29 Temperature Limit
30 Displacer Length
31 Displacer Diameter
32 Displacer Weight
33 Universal rev
34 Fld dev rev
35 Software rev
36 Num req preams
48-635 E3 Modulevel Displacer Level Transmitter