N2893A Datasheet, PDF (22/29 Pages) List of Unclassifed Manufacturers – InfiniiVision Oscilloscope Probes and Accessories

22 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Data Sheet
High-Sensitivity Current Probes (continued)
Probe characteristics and specification
Bandwidth (–3 dB)
Zoom-out channel: DC to 3 MHz
Zoom-in channel: DC to 500 kHz
Risetime (Tr = 0.35/bandwidth, 10% - 90%)
Minimum measurable current*
Maximum measurable current
DC amplitude accuracy
Gain***
Max input voltage
Output impedance
Standard accessories
Compatible InfiniiVision oscilloscopes
Max number of probes supported by 3000 X-Series
Max number of probes supported by 4000 X-Series
Zoom-out channel: < 0.116 μsec
Zoom-in channel: < 0.7 μsec
250 μA (with N2822A 20 mΩ, 500 mW)
50 μA (with N2824A 100 mΩ, 500 mW)
5 mA (with N2825A user-defined 1 mΩ, 500 mW)
50 μA (with N2825A user-defined 1 kΩ, 500 mW)
5 A (with N2822A 20 mΩ, 500 mW)
2.2 A (with N2824A 100 mΩ, 500 mW)
5 A** (with N2825A user-defined 1 mΩ, 500 mW)
1.2 mA** (with N2825A user-defined 1 kΩ, 500 mW)
± 3% or 10 μA (whichever is greater)
Zoom-in channel: 300 ± 3%
Zoom-out channel: 1.97 ± 3%
± 12 V
1 MΩ
– 1 each 20 mΩ resistor sensor head
– 1 each 100 mΩ resistor sensor head
– 1 each user defined resistor sensor head
– 5 each twisted leads (22 AWG) with sockets
– 5 each twisted leads (22 AWG) without sockets
– 5 each MBB headers
– 5 each MBB receptacles
– 1 each ground lead
– 1 each screw driver
– 1 each passive cable (with N2820A only)
– 1 each user guide manual (English)
InfiniiVision 3000 X-Series (with software version 2.30 or higher)
InfiniiVision 4000 X-Series (with software version 3.10 or higher)
InfiniiVision 6000 X-Series (with software version 6.00 or higher)
Two N2820A probes using both pods or two N2821A probes
Two N2820A probes using both pods, four N2820A probes using only the primary pod, or
four N2821A probes
* Vsupply is equal to 5 V, solder attached.
** Max current varies with max resistor power rating. The examples in the table assume 500 mW power rating.
*** Denotes warrantied specification after 20-minute warm up. All others entries in the table are characteristics
Ordering information for Keysight current probes
Model numbers
N2820A
N2821A
Replacement part numbers
N2822A
N2824A
N2825A
N2826A
N2827A
N2828A
N2829A
Descriptions
High-sensitivity 2-ch current probe
High-sensitivity 1-ch current probe
20 mΩ resistor tips
100 mΩ resistor tips
User-defined resistor tips
Replacement wires (15.5 cm, 22 AWG bare wires) (qty 5)
Passive cable (for N2820A secondary channel)
Replacement MBB (Make Before Break) headers (qty 5)
Replacement MBB (Make Before Break) receptacles and 15.5 cm, AWG 22 socketed wires (qty 5 each)