N2893A Datasheet, PDF (15/29 Pages) List of Unclassifed Manufacturers – InfiniiVision Oscilloscope Probes and Accessories

15 | Keysight | InfiniiVision Oscilloscope Probes and Accessories - Data Sheet
Single-ended Active
Probes
N2795A/96A/97A low-cost
single-ended active voltage
The N2795A/96A/97A are equipped with
a white LED headlight to illuminate the
circuit under test. The probes are powered
directly by the InfiniiVision and Infiniium
Autoprobe interface, eliminating the need
for an additional power supply. The probes
also come with a number of accessories
that allow for easy connections to the
circuit under test.
–  High resistance (1MΩ) and low
capacitance (1 pF) input for low
loading
–  Wide input dynamic range (±8 V) and
offset range (±12 V for N2796A/97A,
±8 V for N2795A)
–  Built-in headlight
–  Direct connection to AutoProbe
interface (no power supply required)
–  N2797A for extreme temperature
environmental chamber testing at –40
to +85 °C
The N2795A/96A are a new generation of
low-cost, 1 to 2 GHz single-ended active
probes with the AutoProbe interface
(compatible with Keysight’s InfiniVision
and Infiniium family of oscilloscopes).
These probes integrate many of the
characteristics needed for today’s
general-purpose, high-speed
probing–especially in digital system
design, component design/
characterization, and educational research
applications. Its 1 MΩ input resistance and
extremely low input capacitance (1 pF)
provide ultra low loading of the DUT. This,
accompanied with superior signal fidelity,
makes these probes useful for most of
today’s digital logic voltages. Testing
devices over extreme temperature ranges
is quite common these days. The N2797A
1.5 GHz single-ended active probe is the
industry’s first low-cost high input
impedance active probe with rugged
probe tips for environmental chamber
testing of ICs and devices. It gives the
ability to probe signals at drastic
temperature swings ranging from –40 to
+85 °C. The probe provides a 2 m long
cable. Order N2798A for re-ordering
accessories.
Model number
N2795A
N2796A
N2797A
Probe bandwidth* (–3 dB)
1 GHz
2 GHz
1.5 GHz
Risetime
System bandwidth
Attenuation ratio (at dc)
Input dynamic range
Non-destructive input voltage
Offset range
DC offset error (output zero)
Low frequency accuracy
Input resistance*
Input capacitance
Output impedance
Max number of probes
supported by InfiniiVision 3000
X-/5000/6000/7000 Series**
Max number of probes
supported by InfiniiVision
4000X, 6000X
350 ps
500/600 MHz with
Keysight’s 500/600 MHz
InfiniiVision/Infiniium,
1 GHz with 1 GHz
InfiniiVision 3000 X, 4000 X
10:1 ± 0.5%
–8 to +8 V (DC or peak AC)
–20 to +20 V
±8 V
±1 mV
0.5% at 70 Hz, 1 Vpp
1 MΩ
1 pF
50 Ω
2
4
175 ps
233 psec
1 GHz with Keysight’s
1 GHz InfiniiVision/Infiniium, 1.5 GHz
with Keysight’s 1.5 GHz InfiniiVision
4000 X,
6000 X
±12 V
* Denotes warranted electrical specifications after 20 minute warm-up, all others are typical
** The N2797A is compatible with 3000 X-, 4000 X- and 6000 X-Series only.
Replacement accessories
N4839A
N4840A
N4841A
N4842A
N4843A
N4844A
N4845A
N4846A
Dual lead socketed adapter, 6 cm, qty 2
Dual lead solder-in adapter, 5 cm, qty 2
Dual lead socketed adapter, 9 cm, qty 2
Dual pin PCB header, qty 2
Solderable tips, qty 10
Right angle ground lead, 5 cm, qty 2
Ground blade, qty 2
Offset ground, qty 2
For more information about N2795A/96A/97A active probe, refer to the Keysight
N2795A/96A/97A active probe data sheet, literature number 5990-6480EN.