20-101-1051 Datasheet, PDF (17/165 Pages) List of Unclassifed Manufacturers – C-Programmable Core Module with NAND Flash Mass Storage and Ethernet

2.2.2 Step 2 — Connect Serial Programming Cable
The serial programming cable connects the RCM3365/RCM3375 to the PC running
Dynamic C to download programs and to monitor the module during debugging.
Connect the 10-pin connector of the serial programming cable labeled PROG to header J1
on the RCM3365/RCM3375 module as shown in Figure 3. There is a small dot on the cir-
cuit board next to pin 1 of header J1. Be sure to orient the marked (usually red) edge of the
cable towards pin 1 of the connector. (Do not use the DIAG connector, which is used for a
nonprogramming serial connection.)
alternate
3-pin
power connector
AC adapter
J8
GND
NC
GND
+3.3 V
VBT
VRAM
/RES
SM0
SMODE1
/IORD D2
/IOWR
PG5
PG4 _L1
PG6
PG7
PE0
PE1
PE3
PE4
PE5
R12
PE6
PF7
PF5
R67
PB7
PB6
R68 ^C8
PB5
PB4
R69
PB3
R70
PB2
PB0
/RES_OUT
C1
U4
RCM3300
PROTOTYPING
BOARD
R1
D1
C2
C3
U2
L293D
H-DRIVER
U1 J10
R13
C4
OUT
OUT 00 01 02 03 04 05 06 07
RP1 RP2
U5
R16
R15
PF0_CLKD
PF0_QD
U3
L293D
H-DRIVER
R14
C5
BT1
R52 R53
R60 R61
U7
R8 U6 C6
R9
RABBITNET
J11
ACT
PD7
PD3
PD5
PG3
PG1
PC7
PC5
PC3
PC1
PF0
PF2
PA0
PA2
PA4
PA6
STAT
J9
LINK
PD6
PD2
PD4
PG2
PG0
PC6
PC4
PC2
PC0
PF1
PF3
PA1
PA3
PA5
PA7
GND
S1
RESET
CORE MODULE
GND/EGND
CX1
+5 V
GND
+3.3 _RV _X13
RX14
RX15
RX16
RX17
RX18
+5 V
GND
+3.3 V
R39 J15
J16
JA
R25 R26
S2
U8
C16
R21 R22 R23 R24
Q1 Q2 Q3 Q4
JB
R27 R28
J12
R50
D4 D5 D6 D7
Q6
R49
CORE
S3
DS2 DS3 DS4 DS5 DS6
UX1
SO20W
UX4
DX1
LCD1JA
CX2
UX5
DX2
C19
R42
R40
UX2
SO20W
J13
U9
U10
R35
To
K1
U11 PCU12 COM port
D8
C22
C23
J14
C24
R36
JP5
C26
R38
Blue
KEYPAD DISPLAY BOARD
shrink wrap
C29 C30
Q5
Colored edge LCD1JB
LCD1JC
TxE RxE GND TxF RxF 485+ GND 485–
Programming Cable
J17
R47
Figure 3. Connect Serial Programming Cable and Power Supply
NOTE: Be sure to use the serial programming cable (part number 101-0542) supplied
with this Development Kit—the serial programming cable has blue shrink wrap around
the RS-232 converter section located in the middle of the cable. Programming cables with
clear or red shrink wrap from other Rabbit kits are not designed to work with RCM3365/
RCM3375 modules.
Connect the other end of the serial programming cable to a COM port on your PC.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter (Part No. 20-151--0178) with the serial programming cable
supplied with the RCM3365/RCM3375 Development Kit. Note that not all RS-232/
USB converters work with Dynamic C.
User’s Manual
11