English
Language : 

20-101-1051 Datasheet, PDF (16/165 Pages) List of Unclassifed Manufacturers – C-Programmable Core Module with NAND Flash Mass Storage and Ethernet
2.2 Hardware Connections
There are three steps to connecting the Prototyping Board for use with Dynamic C and the
sample programs:
1. Attach the RCM3365/RCM3375 module to the Prototyping Board.
2. Connect the serial programming cable between the RCM3365/RCM3375 and the worksta-
tion PC or if you have an RCM3365 with RabbitSys firmware you may connect the
RCM3365 and the PC using Ethernet cables.
3. Connect the power supply to the Prototyping Board.
2.2.1 Step 1 — Attach Module to Prototyping Board
Turn the RCM3365/RCM3375 module so that the Ethernet jack is facing the direction shown
in Figure 2 below. Align the pins from headers J3 and J4 on the bottom side of the module into
header sockets JA and JB on the Prototyping Board. The picture card (NAND flash) does not
have to be inserted into connector J6 on the RCM3365/RCM3375 at this time.
RCM3365/
RCM3375
J8
GND
NC
GND
+3.3 V
VBT
VRAM
/RES
SM0
SMODE1
/IORD D2
/IOWR
PG5
PG4 L1
PG6
PG7
PE0
PE1
PE3
PE4
PE5 R12
PE6
PF7
PF5
R67
PB7
PB6
R68 C8
PB5
PB4
R69
R70
PB3
PB2
PB0
/RES_OUT
C1
U4
RCM3300
PROTOTYPING
BOARD
R1
D1
C2
C3
U2
L293D
H-DRIVER
U1 J10
R13
C4
OUT
OUT 00 01 02 03 04 05 06 07
RP1 RP2
U5
R16
R15
PF0_CLKD
PF0_QD
U3
L293D
H-DRIVER
R14
C5
BT1
R52 R53
R60 R61
U7
R8 U6 C6
R9
RABBITNET
J11
Do not press down
here.
J6
ACT
PD7
PD3
PD5
PG3
PG1
PC7
PC5
PC3
PC1
PF0
PF2
PA0
PA2
PA4
PA6
STAT
J9
LINK
PD6
PD2
PD4
PG2
PG0
PC6
PC4
PC2
PC0
PF1
PF3
PA1
PA3
PA5
PA7
GND
S1
RESET
CORE MODULE
GND/EGND
+5 V
GND
+3.3 RV X13
CX1
RX14
RX15
RX16
RX17
RX18
UX1
SO20W
UX4
DX1
JA
JA
R25 R26
S2
U8
C16
R21 R22 R23 R24
JB
Q1 Q2 Q3 Q4
JB
R27 R28
J12
R50
D4 D5 D6 D7
Q6
R49
CORE
S3
DS2 DS3 DS4 DS5 DS6
CX2
UX2
SO20W
J13
U9
C22
C23
J14
C24
UX5
DX2
U10
R35
R36
JP5
C26
R38
TxE RxE GND TxF RxF 485+ GND 485–
CORE LED
+5 V
GND
+3.3 V
R39 J15
J16
LCD1JA
J17
C19
R42
R40
K1
U11
U12
D8
KEYPAD DISPLAY BOARD
C29 C30
Q5
R47
LCD1JB
LCD1JC
Figure 2. Install the RCM3365/RCM3375 Module on the Prototyping Board
NOTE: It is important that you line up the pins on headers J3 and J4 of the RCM3365/
RCM3375 module exactly with the corresponding pins of header sockets JA and JB on
the Prototyping Board. The header pins may become bent or damaged if the pin align-
ment is offset, and the module will not work. Permanent electrical damage to the mod-
ule may also result if a misaligned module is powered up.
Press the module’s pins firmly into the Prototyping Board header sockets—press down in the
area above the header pins using your thumbs or fingers over the header pins as shown in
Figure 2. Do not press down on the picture card connector (J6) unless the picture card is
installed, but rather press down on the circuit board along the edge by the connector. Also, do
not press down on the middle of the module to avoid flexing the module, which could damage
the module or components on the module.
Should you need to remove the module, grasp it with your fingers along the sides by the con-
nectors and gently work the module up to pull the pins away from the sockets where they are
installed. Do not remove the module by grasping it at the top and bottom.
10
RabbitCore RCM3365/RCM3375