DS90UR907Q-Q1 Datasheet, PDF (6/35 Pages) Texas Instruments – 24-Bit Color FPD-Link to FPD-Link II Converter

DS90UR907Q-Q1
SNLS316G – SEPTEMBER 2009 – REVISED DECEMBER 2015
www.ti.com
6.5 Thermal Information
THERMAL METRIC⁽¹⁾
DS90UR907Q-Q1
NJK (WQFN)
UNIT
36 PINS
R_θJA
R_θJC(top)
R_θJB
ψ_JT
ψ_JB
R_θJC(bot)
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
33.8
°C/W
15.8
°C/W
7.2
°C/W
0.2
°C/W
7.1
°C/W
2.6
°C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
6.6 DC Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.^(1)(2)(3)
PARAMETER
TEST CONDITIONS
PIN/FREQ.
MIN
LVCMOS INPUT DC SPECIFICATIONS
V_IH
High Level Input Voltage
V_DDIO = 3 to 3.6 V
V_DDIO = 1.71 to 1.89 V
2.2
0.65* V_DDIO
V_DDIO = 3 to 3.6 V
PDB,
V_IL
Low Level Input Voltage
V_DDIO = 1.71 to 1.89 V
VODSEL,
MAPSEL,
I_IN
Input Current
V_IN = 0 V or V_DDIO
V_DDIO = 3
to 3.6 V
V_DDIO = 1.7
to 1.89 V
CONFIG[1:0],
BISTEN
GND
GND
–15
–15
FPD-LINK LVDS RECEIVER DC SPECIFICATIONS
V_TH
Differential Threshold High
Voltage
V_TL
Differential Threshold Low
Voltage
V_CM = 1.2 V, Figure 1
|V_ID|
Differential Input Voltage
Swing
RxIN[3:0]+/-,
RxCLKIN+/-,
–100
200
V_CM
Common Mode Voltage
V_DDIO = 3.3 V
V_DDIO = 1.8 V
0
0
I_IN
Input Current
−15
TYP
±1
±1
1.2
1.2
±1
MAX UNIT
V_DDIO
V
V_DDIO
0.8
0.35* ^V
V_DDIO
15
μA
15
100
mV
600 mV
2.4
V
1.55
15 μA
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms at V_DD = 3.3 V, Ta = 25°C, and at the Recommended Operation Conditions at the
time of product characterization and are not ensured.
(3) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD, ΔVOD, VTH and VTL which are differential voltages.
6
Submit Documentation Feedback
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: DS90UR907Q-Q1