DS90UR907Q-Q1 Datasheet, PDF (5/35 Pages) Texas Instruments – 24-Bit Color FPD-Link to FPD-Link II Converter

www.ti.com
6 Specifications
DS90UR907Q-Q1
SNLS316G – SEPTEMBER 2009 – REVISED DECEMBER 2015
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)⁽¹⁾⁽²⁾
Supply voltage – V_DDn (1.8 V)
Supply voltage – V_DDIO
LVCMOS I/O voltage
LVDS input voltage
Driver output voltage
Junction temperature
Storage temperature
MIN
–0.3
−0.3
−0.3
−0.3
−0.3
−65
MAX
2.5
4
V_DDIO + 0.3
V_DDIO + 0.3
V_DDn + 0.3
150
150
UNIT
V
V
V
V
V
°C
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
6.2 ESD Ratings—JEDEC
V_(ESD) Electrostatic discharge
Human-body model (HBM), per AEC Q100-002⁽¹⁾
Charged-device model (CDM), per AEC Q100-011
Machine model
VALUE
±8000
±1250
±250
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
UNIT
V
6.3 ESD Ratings—IEC and ISO
V_(ESD)
Electrostatic discharge
R_D = 330 Ω, C_S = 150 pF
R_D = 330 Ω, C_S = 150 and 330 pF
R_D = 2 kΩ, C_S = 150 and 330 pF
IEC, powered-up only contact discharge
(R_IN+, R_IN−)
IEC, powered-up only air-gap discharge
(R_IN+, R_IN−)
ISO10605 contact discharge (R_IN+, R_IN−)
ISO10605 air-gap discharge (R_IN+, R_IN−)
ISO10605 contact discharge (R_IN+, R_IN−)
ISO10605 air-gap discharge (R_IN+, R_IN−)
VALUE
≥±6000
≥±30000
≥±8000
≥±15000
≥±8000
≥±15000
UNIT
V
V
V
6.4 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
Supply Voltage (V_DDn)
LVCMOS Supply Voltage (V_DDIO)
OR
1.71
1.8
1.89
V
1.71
1.8
1.89
V
LVCMOS Supply Voltage (V_DDIO)
Operating Free Air Temperature (T_A)
RxCLKIN Frequency
Supply Noise⁽¹⁾
3
3.3
3.6
V
−40
25
105
°C
5
65
MHz
100
mV_P-P
(1) Supply noise testing was done with minimum capacitors on the PCB. A sinusoidal signal is AC coupled to the V_DDn (1.8 V) supply with
amplitude = 100 mVp-p measured at the device V_DDn pins. Bit error rate testing of input to the Ser and output of the Des with 10 meter
cable shows no error when the noise frequency on the Ser is less than 750 kHz. The Des on the other hand shows no error when the
noise frequency is less than 400 kHz.
Copyright © 2009–2015, Texas Instruments Incorporated
Product Folder Links: DS90UR907Q-Q1
Submit Documentation Feedback
5