MSP430F5229 Datasheet, PDF (24/121 Pages) Texas Instruments – MSP430F522x and MSP430F521x Mixed-Signal Microcontrollers

MSP430F5229, MSP430F5227, MSP430F5224, MSP430F5222
MSP430F5219, MSP430F5217, MSP430F5214, MSP430F5212
SLAS718E – NOVEMBER 2012 – REVISED MAY 2014
www.ti.com
5.10 Leakage Current – General-Purpose I/O DVCC Domain
(P1.0 to P1.3, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
I_lkg(Px.y)
PARAMETER
High-impedance leakage current
TEST CONDITIONS
(1) (2)
V_CC
1.8 V, 3 V
MIN MAX UNIT
-50
50 nA
(1) The leakage current is measured with V_SS or V_CC applied to the corresponding pins, unless otherwise noted.
(2) The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup or pulldown resistor is
disabled.
5.11 Leakage Current – General-Purpose I/O DVIO Domain
(P1.4 to P1.7, P2.0 to P2.7, P3.0 to P3.4, P4.0 to P4.7, P7.0 to P7.5)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
I_lkg(Px.y)
PARAMETER
High-impedance leakage current
TEST CONDITIONS
(2) (3)
V_IO ⁽¹⁾
MIN
1.62 V to 1.98 V -50
MAX UNIT
50 nA
(1) In all test conditions, V_IO ≤ V_CC.
(2) The leakage current is measured with V_SS or V_IO applied to the corresponding pins, unless otherwise noted.
(3) The leakage of the digital port pins is measured individually. The port pin is selected for input and the pullup or pulldown resistor is
disabled.
5.12 Outputs – General-Purpose I/O DVCC Domain (Full Drive Strength)
(P1.0 to P1.3, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V_OH High-level output voltage
V_OL Low-level output voltage
TEST CONDITIONS
I_(OHmax) = –3 mA ⁽¹⁾
I_(OHmax) = –10 mA ⁽²⁾
I_(OHmax) = –5 mA⁽¹⁾
I_(OHmax) = –15 mA⁽²⁾
I_(OLmax) = 3 mA ⁽¹⁾
I_(OLmax) = 10 mA⁽²⁾
I_(OLmax) = 5 mA ⁽¹⁾
I_(OLmax) = 15 mA⁽²⁾
V_CC
1.8 V
3V
1.8 V
3V
MIN
V_CC – 0.25
V_CC – 0.60
V_CC – 0.25
V_CC – 0.60
V_SS
V_SS
V_SS
V_SS
MAX
V_CC
V_CC
V_CC
V_CC
V_SS + 0.25
V_SS + 0.60
V_SS + 0.25
V_SS + 0.60
UNIT
V
V
(1) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage drop
specified.
(2) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined should not exceed ±100 mA to hold the maximum voltage
drop specified.
5.13 Outputs – General-Purpose I/O DVCC Domain (Reduced Drive Strength)
(P1.0 to P1.3, P5.0 to P5.5, P6.0 to P6.7, PJ.0 to PJ.3)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)⁽¹⁾
PARAMETER
V_OH
High-level output voltage
V_OL
Low-level output voltage
TEST CONDITIONS
I_(OHmax) = –1 mA ⁽²⁾
I_(OHmax) = –3 mA ⁽³⁾
I_(OHmax) = –2 mA⁽²⁾
I_(OHmax) = –6 mA⁽³⁾
I_(OLmax) = 1 mA ⁽²⁾
I_(OLmax) = 3 mA ⁽³⁾
I_(OLmax) = 2 mA ⁽²⁾
I_(OLmax) = 6 mA ⁽³⁾
V_CC
1.8 V
3.0 V
1.8 V
3.0 V
MIN
V_CC – 0.25
V_CC – 0.60
V_CC – 0.25
V_CC – 0.60
V_SS
V_SS
V_SS
V_SS
MAX
V_CC
V_CC
V_CC
V_CC
V_SS + 0.25
V_SS + 0.60
V_SS + 0.25
V_SS + 0.60
UNIT
V
V
(1) Selecting reduced drive strength may reduce EMI.
(2) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop
specified.
(3) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined, should not exceed ±100 mA to hold the maximum voltage
drop specified.
24
Specifications
Copyright © 2012–2014, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: MSP430F5229 MSP430F5227 MSP430F5224 MSP430F5222 MSP430F5219 MSP430F5217
MSP430F5214 MSP430F5212