OMAP5912ZZG Datasheet, PDF (46/269 Pages) Texas Instruments – This data sheet revision history highlights the technical changes made to SPRS231D to generate SPRS231E

Introduction
Table 2−3. ZDY/GDY Package Terminal Characteristics (Continued)
ZDY/
GDY
BALL
NO.
SIGNAL NAME
TYPE^†
MUX CTRL SETTING PULLUP/
(see Notes 3 and 4) PULLDN^‡
BUFFER
STRENGTH^§
OTHER^¶
RESET
STATE^#
SUPPLY
H13
CAM.D[3]
ETM.D[3]
I
Reg5[11:9] = 000
PU20,
2 mA (Lv)
A, F
O
Reg5[11:9] = 001
PD20
3 mA (Hv)
Z
DV_DD8
UART3.RX
I
Reg5[11:9] = 010
GPIO31
I/O
Reg5[11:9] = 111
J14
CAM.D[2]
ETM.D[2]
I
Reg5[14:12] = 000
PU20,
2 mA (Lv)
A, F
O
Reg5[14:12] = 001
PD20
3 mA (Hv)
Z
DV_DD8
UART3.CTS
I
Reg5[14:12] = 010
GPIO30
I/O
Reg5[14:12] = 111
J16
CAM.D[1]
ETM.D[1]
I
Reg5[17:15] = 000
PU20,
2 mA (Lv)
A, F
O
Reg5[17:15] = 001
PD20
3 mA (Hv)
Z
DV_DD8
UART3.RTS
O
Reg5[17:15] = 010
GPIO29
I/O
Reg5[17:15] = 111
J17
CAM.D[0]
ETM.D[0]
I
Reg5[20:18] = 000
PU20,
2 mA (Lv)
A, F
O
Reg5[20:18] = 001
PD20
3 mA (Hv)
Z
DV_DD8
MPUIO12
I/O
Reg5[20:18] = 010
MMC2.DAT3
I/O
Reg5[20:18] = 011
J13
CAM.VS
ETM.PSTAT[2]
I
Reg5[23:21] = 000
PU20,
2 mA (Lv)
A, F
O
Reg5[23:21] = 001
PD20
3 mA (Hv)
Z
DV_DD8
MPUIO14
I/O
Reg5[23:21] = 010
MMC2.DAT1
I/O
Reg5[23:21] = 011
J12
CAM.HS
ETM.PSTAT[1]
I
Reg5[26:24] = 000
PU20,
2 mA (Lv)
A, F
O
Reg5[26:24] = 001
PD20
3 mA (Hv)
Z
DV_DD8
UART2.CTS
I
Reg5[26:24] = 010
MMC2.DAT0
I/O
Reg5[26:24] = 011
GPIO38
I/O
Reg5[26:24] = 111
† _{I = Input, O = Output, Z = High-Impedance}
‡ _{PD20 = 20-µA internal pulldown, PD100=100-µA internal pulldown, PU20 = 20-µA internal pullup, PU100 = 100-µA internal pullup. Pullup or}
pulldown can be enabled or disabled by software.
§ _{Lv = Low voltage (1.65 V), Hv = High voltage (2.5 V)}
¶ _{A = Standard LVCMOS input/output}
G1 = Terminal may be gated by BFAIL
B = SUBLVDS input/ouput
G2 = Terminal may be gated by GPIO9 and MPUIO3
C = USB transceiver input/ouput
G3 = Terminal my be gated by BFAIL and OMAP5912 Internal Reset
D = I²C input/output buffers
H1 = Terminal may be 3-stated by BFAIL input
E = Analog oscillator terminals
H3 = MCSI1.DOUT pin can be forced into a high-impedance
F = Boundary-scannable terminal
state by the OMAP5912 HIGH_IMP3 control bit
K = Output buffer includes a serial resistor of 20 Ω to match with PCB line impedance and ensure proper signal integrity
# _{Z = High-Impedance, LZ = Low-Impedance (pin is driven), 1 = Output driven high, 0 = Output driven low}
|| _{Slew time constraint of the EXT_DMA_REQ1 must be lower than or equal to 10 ns (from 10% to 90% of DVDD) in Mode 1.}
kSlew time constraint of the EXT_DMA_REQ0 must be lower than or equal to 10 ns (from 10% to 90% of DV_DD) in Mode 1.
NOTES: 3. NA denotes no multiplexing on the ball
4. ‘Regx’ denotes the terminal multiplexing register that controls the specified terminal where Regx = FUNC_MUX_CTRL_x
46 SPRS231E
December 2003 − Revised December 2005