K5A3X80YTC Datasheet, PDF (27/45 Pages) Samsung semiconductor – MCP MEMORY

K5A3x80YT(B)C
Preliminary
MCP MEMORY
DC CHARACTERISTICS(Continued)
Parameter
Automatic Sleep Mode
Voltage for WP/ACC Block
Temporarily Unprotect and
Flash _{Program Acceleration (4)}
Symbol
Test Conditions
ISB3 VIH=Vcc_F±0.3V, VIL=VSS±0.3V, OE=VIL, IOL=IOH=0
VHH Vcc_F = 3.0V ± 0.3V
Min Typ Max Unit
-
5 18 µA
8.5 - 12.5 V
Voltage for Autoselect and
Block Protect (4)
VID Vcc_F = 3.0V ± 0.3V
8.5 - 12.5 V
Low Vcc_F Lock-out Voltage (5) VLKO
1.8 - 2.5 V
Operating Current
Cycle time=1µs, 100% duty, CS1_S≤0.2V,
ICC1
CS2_S≥Vcc_S-0.2V, LB≤0.2V and/or UB≤0.2V
All outputs open, VIN≤0.2V or VIN≥Vcc_S-0.2V,
BYTE_S=Vcc_S± 0.3V or Vss± 0.3V
-
-
3 mA
SRAM
ICC2 Cycle time=Min, 100% duty, CS1_S=VIL, CS2_S=VIH,
LB=VIL and/or UB= VIL, All outputs open, VIN=VIL or
-
22 28 mA
VIH, BYTE_S=Vcc_S± 0.3V or Vss± 0.3V
Standby Current
CS1_S≥Vcc_S-0.2V, CS2_S≥Vcc_S-0.2V (CS1_S controlled)
ISB
or CS2_S≤0.2V (CS2_S controlled),
BYTE_S=Vcc_S± 0.3V or Vss± 0.3V,
-
Other input =0~Vcc_S
0.5 15 µA
NOTES:
1. The ICC current listed includes both the DC operating current and the frequency dependent component(at 5 MHz).
The read current is typically 14 mA (@ Vcc_F=3.0V , OE at VIH.)
2. ICC active during Internal Routine(program or erase) is in progress.
3. ICC active during Read while Write is in progress.
4. The high voltage ( VHH or VID ) must be used in the range of Vcc_F = 3.0V ± 0.3V
5. Not 100% tested.
6. Typical values are measured at Vcc_F = Vcc_S = 3.0V, Ta=25°C , not 100% tested.
CAPACITANCE(TA = 25 °C, Vcc_F = Vcc_S = 3.3V, f = 1.0MHz)
Item
Symbol
Test Condition
Min
Max
Unit
Input Capacitance
CIN
VIN=0V
-
18
pF
Output Capacitance
COUT
VOUT=0V
-
20
pF
Control Ball Capacitance
CIN2
VIN=0V
-
18
pF
NOTE: Capacitance is periodically sampled and not 100% tested.
AC TEST CONDITION
Parameter
Input Pulse Levels
Input Rise and Fall Times
Input and Output Timing Levels
Output Load
Value
0V to Vcc
5ns
Vcc/2
CL = 30pF
Vcc
Vcc/2
0V
Input & Output
Test Point
Vcc/2
Input Pulse and Test Point
- 27 -
Device
CL
* CL= 30pF including Scope
and Jig Capacitance
Output Load
Revision 0.0
November 2002