M37160M8 Datasheet, PDF (93/131 Pages) Renesas Technology Corp – SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER

M37160M8/MA/MF-XXXSP/FP,M37160EFSP/FP
12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8.86 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Symbol
Parametear
Test conditions
Limits
Unit ^Test
Min. Typ. Max.
circuit
VCC = 5.5V,
f(XIN) = 8.86MHz
OSD OFF
OSD ON
15 30
mA
30 45
ICC
VOH
VOL
VT+ –VT–
IIZH
IIZL
RBS
Power source current
System operation
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 32kHz,
OSD OFF,
Low-power dissipation mode set
(CM5 = “0”, CM6 = “1”)
60 200 µA
1
Wait mode
VCC = 5.5 V, f(XcIN) = 4.43 MHz
VCC = 5.5 V, f(XIN) = 0,
f(XCIN) = 32 kHz,
Low-power dissipation mode set
1
2 mA
25 100 µA
(CM5 = “0”, CM6 = “1”)
Stop mode
HIGH output voltage P10–P16, P20–P27,
P30, P31, P52–P55,
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 0
VCC = 4.5 V
IOH = –0.5 mA
1
10
2.4
V2
LOW output voltage
P00–P07, P10,
P15, P16, P20–P23,
P52–P55
VCC = 4.5 V
IOL = 0.5 mA
0.4 V
LOW output voltage P24– P27
VCC = 4.5 V
3.0
IOL = 10.0 mA
LOW output voltage P11–P14, P30, P32
VCC = 4.5 V
IOL = 3 mA
0.4
IOL = 6 mA
0.6
Hysteresis (See note 6)
____________
RESET, P50, P51, INT1, INT2,
INT3, TIM2, TIM3, SIN, SCLK, SCL1,
SCL2, SCL3, SDA1, SDA2, SDA3
VCC = 5.0 V
0.5 1.3 _V
3
HIGH input leak current
P00–P07, P10–P16, P20–P27,
____________
P30, P31,P35–P37, RESET, P50, P51,
VCC = 5.5 V
VI = 5.5 V
5 µA ⁴
LOW input leak current
P00–P07, P10–P16, P20–P27, P30, P31,
____________
P35–P37, P50, P51, RESET
VCC = 5.5 V
VI = 0 V
5 ^{µA 4}
I²C-BUS • BUS switch connection resistor
(between SCL1 and SCL2, SDA1 and SDA2)
VCC = 4.5 V
130 Ω 5
Notes 1: The total current that flows out of the IC must be 20 mA or less.
2: The total input current to IC (IOL1 + IOL2) must be 30 mA or less.
3: The total average input current for ports P24–P27 and AVCC–VSS to IC must be 20 mA or less.
4: Connect 0.1 µF or more capacitor externally between the power source pins VCC–VSS so as to reduce power source noise.
Also connect 0.1 µF or more capacitor externally between the pins VCC–CNVSS.
5: P06, P07, P16, P23, P24, P25 have hysteresis when used as interrupt input pins or timer input pins. P11–P14, P30, P31 have hysteresis when used as multi-
master I²C-BUS interface ports. P20–P22 have hysteresis when used as serial I/O pins.
6: Pin names in each parameter are described as below.
(1) Dedicated pins: dedicated pin names.
(2) Double-/triple-function ports
• Same limits: I/O port name.
• Functions other than ports vary from I/O port limits : function pin name.
Rev.1.01 2003.11.13 page 93 of 130