M16C65C_15 Datasheet, PDF (55/112 Pages) Renesas Technology Corp – RENESAS MCU

M16C/65C Group
5. Electrical Characteristics
Table 5.6 A/D Conversion Characteristics (2/2) ⁽¹⁾
V_CC1 = AV_CC = 3.0 to 5.5 V ≥ V_CC2 ≥ V_REF, V_SS = AV_SS = 0 V at T_opr = -20°C to 85°C/-40°C to 85°C unless otherwise
specified.
Symbol
Parameter
Measuring Condition
φAD
A/D operating clock AN0 to AN7 input, 4.0 V ≤ V_CC1 ≤ 5.5 V
frequency
ANEX0 to ANEX1
input
3.2 V ≤ V_CC1 ≤ 4.0 V
3.0 V ≤ V_CC1 ≤ 3.2 V
AN0_0 to AN0_7
input, AN2_0 to
AN2_7 input
4.0 V ≤ V_CC2 ≤ 5.5 V
3.2 V ≤ V_CC2 ≤ 4.0 V
3.0 V ≤ V_CC2 ≤ 3.2 V
-
Tolerance level impedance
D_NL
Differential non-linearity error
(4)
-
Offset error
(4)
Standard
Min. Typ. Max.
2
25
2
16
2
10
2
25
2
16
2
10
3
±1
±3
Unit
MHz
MHz
MHz
MHz
MHz
MHz
kΩ
LSB
LSB
-
Gain error
(4)
±3 LSB
t_CONV
t_SAMP
V_REF
V_IA
10-bit conversion time
Sampling time
Reference voltage
Analog input voltage ^{(2), (3)}
V_CC1 = 5 V, φAD = 25 MHz
1.60
0.60
3.0
0
μs
μs
V_CC1
V
V_REF
V
Notes:
1. Use when AV_CC = V_CC1.
2. When V_CC1 ≥ V_CC2, set as below:
Analog input voltage (AN0 to AN7, ANEX0, and ANEX1) ≤ V_CC1
Analog input voltage (AN0_0 to AN0_7 and AN2_0 to AN2_7) ≤ V_CC2.
3. When analog input voltage is over reference voltage, the result of A/D conversion is 3FFh.
4. Flash memory rewrite disabled. Except for the analog input pin, set the pins to be measured as input ports and
connect them to V_SS. See Figure 5.2 “A/D Accuracy Measure Circuit”.
5.1.4 D/A Conversion Characteristics
Table 5.7 D/A Conversion Characteristics
V_CC1 = AV_CC = V_REF = 3.0 to 5.5 V, V_SS = AV_SS = 0 V at T_opr = -20°C to 85°C/-40°C to 85°C unless otherwise specified.
Symbol
Parameter
Measuring Condition
Standard
Unit
Min. Typ. Max.
-
Resolution
8
Bits
-
Absolute Accuracy
2.5 LSB
t_SU
Setup Time
3
μs
R_O
Output Resistance
5
6
8.2 kΩ
I_VREF
Reference Power Supply Input Current _{See Notes} ¹ _and ²
1.5 mA
Notes:
1. This applies when using one D/A converter, with the D/A register for the unused D/A converter set to 00h.
2. The current consumption of the A/D converter is not included. Also, the I_VREF of the D/A converter will flow even
if the ADSTBY bit in the ADCON1 register is 0 (A/D operation stopped (standby)).
R01DS0015EJ0110 Rev.1.10
Jul 31, 2012
Page 55 of 109