M16C65C_15 Datasheet, PDF (18/112 Pages) Renesas Technology Corp – RENESAS MCU

M16C/65C Group
1. Overview
1.6 Pin Functions
Table 1.12 Pin Functions for the 128-Pin Package (1/3)
Signal Name
Power supply
input
Analog power
supply input
Reset input
CNVSS
Pin Name
VCC1,
VCC2,
VSS
AVCC,
AVSS
RESET
CNVSS
I/O Power Supply
Description
I
-
Apply 2.7 to 5.5 V to pins VCC1 and VCC2 (VCC1 ≥ VCC2),
and 0 V to the VSS pin.
This is the power supply for the A/D and D/A converters.
I
VCC1 Connect the AVCC pin to VCC1, and connect the AVSS pin
to VSS.
I
VCC1 Driving this pin low resets the MCU.
Input pin to switch processor modes. After a reset, to start
I
VCC1
operating in single-chip mode, connect the CNVSS pin to
VSS via a resistor. To start operating in microprocessor
mode, connect the pin to VCC1.
External data bus
width select input
BYTE
I
D0 to D7 I/O
D8 to D15 I/O
VCC1
VCC2
VCC2
Input pin to select the data bus of the external area. The data
bus is 16 bits when it is low and 8 bits when it is high. This
pin must be fixed either high or low. Connect the BYTE pin to
VSS in single-chip mode.
Inputs or outputs data (D0 to D7) while accessing an
external area with a separate bus.
Inputs or outputs data (D8 to D15) while accessing an
external area with a 16-bit separate bus.
Bus control
pins
A0 to A19
O
A0/D0 to
A7/D7
I/O
A1/D0 to
A8/D7
I/O
CS0 to CS3 O
WRL/WR
WRH/BHE O
RD
ALE
O
HOLD
I
HLDA
O
RDY
I
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
VCC2
Outputs address bits A0 to A19.
Inputs or outputs data (D0 to D7) and outputs address bits
(A0 to A7) by timesharing, while accessing an external area
with an 8-bit multiplexed bus.
Inputs or outputs data (D0 to D7) and outputs address bits
(A1 to A8) by timesharing, while accessing an external area
with a 16-bit multiplexed bus.
Outputs chip-select signals CS0 to CS3 to specify an
external area.
Outputs WRL, WRH, (WR, BHE), and RD signals. WRL and
WRH can be switched with BHE and WR.
• WRL, WRH, and RD selected
If the external data bus is 16 bits, data is written to an even
address in an external area when WRL is driven low. Data
is written to an odd address when WRH is driven low. Data
is read when RD is driven low.
• WR, BHE, and RD selected
Data is written to an external area when WR is driven low.
Data in an external area is read when RD is driven low. An
odd address is accessed when BHE is driven low. Select
WR, BHE, and RD when using an 8-bit external data bus.
Outputs an ALE signal to latch the address.
HOLD input is unavailable. Connect the HOLD pin to VCC2
via a resistor (pull-up).
In a hold state, HLDA outputs a low-level signal.
The MCU bus is placed in wait state while the RDY pin is
driven low.
Power supply: VCC2 is used to supply power to the external bus associated pins. The dual power supply configuration
allows VCC2 to interface at a different voltage than VCC1.
R01DS0015EJ0110 Rev.1.10
Jul 31, 2012
Page 18 of 109