ISL6322G Datasheet, PDF (21/39 Pages) Intersil Corporation – Two-Phase Buck PWM Controller with Integrated MOSFET Drivers, I2C Interface and Phase Dropping

ISL6322G
1kΩ resistor between the DAC and the REF pin, and the
external capacitor C_REF, between the REF pin and ground.
For AMD VID transitions C_REF should be a 1000pF
capacitor.
User Selectable Adaptive Deadtime Control
Techniques
The ISL6322G integrated drivers incorporate two different
adaptive deadtime control techniques, which the user can
choose between. Both of these control techniques help to
minimize deadtime, resulting in high efficiency from the reduced
freewheeling time of the lower MOSFET body-diode
conduction, and both help to prevent the upper and lower
MOSFETs from conducting simultaneously. This is
accomplished by ensuring either rising gate turns on its
MOSFET with minimum and sufficient delay after the other has
turned off.
The difference between the two adaptive deadtime control
techniques is the method in which they detect that the lower
MOSFET has transitioned off in order to turn on the upper
MOSFET. The state of the internal I²C registers determines
which of the two control techniques is active (refer beginning
on page 27 for details of controlling deadtime control with
I²C). The default setting is PHASE Detect. If the PHASE
Detect Scheme is chosen, the voltage on the PHASE pin is
monitored to determine if the lower MOSFET has
transitioned off or not. Choosing the LGATE Detect Scheme
instructs the controller to monitor the voltage on the LGATE
pin to determine if the lower MOSFET has turned off or not.
For both schemes, the method for determining whether the
upper MOSFET has transitioned off in order to signal to turn
on the lower MOSFET is the same.
PHASE DETECT
For the PHASE detect scheme, during turn-off of the lower
MOSFET, the PHASE voltage is monitored until it reaches a
-0.3V/+0.8V (forward/reverse inductor current). At this time the
UGATE is released to rise. An auto-zero comparator is used to
correct the r_DS(ON) drop in the phase voltage preventing false
detection of the -0.3V phase level during r_DS(ON) conduction
period. In the case of zero current, the UGATE is released after
35ns delay of the LGATE dropping below 0.5V. When LGATE
first begins to transition low, this quick transition can disturb the
PHASE node and cause a false trip, so there is 20ns of
blanking time once LGATE falls until PHASE is monitored.
Once the PHASE is high, the advanced adaptive
shoot-through circuitry monitors the PHASE and UGATE
voltages during a PWM falling edge and the subsequent
UGATE turn-off. If either the UGATE falls to less than 1.75V
above the PHASE or the PHASE falls to less than +0.8V, the
LGATE is released to turn-on.
LGATE DETECT
For the LGATE detect scheme, during turn-off of the lower
MOSFET, the LGATE voltage is monitored until it reaches
1.75V. At this time the UGATE is released to rise.
Once the PHASE is high, the advanced adaptive
shoot-through circuitry monitors the PHASE and UGATE
voltages during a PWM falling edge and the subsequent
UGATE turn-off. If either the UGATE falls to less than 1.75V
above the PHASE or the PHASE falls to less than +0.8V, the
LGATE is released to turn-on.
Internal Bootstrap Device
All three integrated drivers feature an internal bootstrap
schottky diode. Simply adding an external capacitor across
the BOOT and PHASE pins completes the bootstrap circuit.
The bootstrap function is also designed to prevent the
bootstrap capacitor from overcharging due to the large
negative swing at the PHASE node. This reduces voltage
stress on the boot to phase pins.
The bootstrap capacitor must have a maximum voltage
rating above PVCC + 4V and its capacitance value can be
chosen from Equation 13:
C_{BOOT_CAP} ≥ _Δ-----_V----_B-^Q---_O--^G--_O--^A---_T-^T--_{_}-^E--_C----_A----_P-
Q_GATE=
Q_{-----G-----1----}⋅_---P_-----V_----C_-----C_---
V_GS1
⋅
N_Q
1
(EQ. 13)
where Q_G1 is the amount of gate charge per upper MOSFET
at V_GS1 gate-source voltage and N_Q1 is the number of
control MOSFETs. The ΔV_{BOOT_CAP} term is defined as the
allowable droop in the rail of the upper gate drive.
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2 _20nC
Q_GATE = 100nC
50nC
0.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
ΔV_{BOOT_CAP} (V)
FIGURE 9. BOOTSTRAP CAPACITANCE vs BOOT RIPPLE
VOLTAGE
Gate Drive Voltage Versatility
The ISL6322G provides the user flexibility in choosing the
gate drive voltage for efficiency optimization. The controller
ties the upper and lower drive rails together. Simply applying
a voltage from 5V up to 12V on PVCC sets both gate drive
rail voltages simultaneously.
21
FN6715.0
May 22, 2008