MC35XS3400 Datasheet, PDF (6/45 Pages) Freescale Semiconductor, Inc – Quad High Side Switch (Quad 35mΩ)

ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics
Characteristics noted under conditions 6.0V ≤ V_PWR ≤ 20V, 3.0V ≤ V_DD ≤ 5.5V, -40°C ≤ T_A ≤ 125°C, GND = 0V, unless
otherwise noted. Typical values noted reflect the approximate parameter means at T_A = 25°C under nominal conditions, unless
otherwise noted.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER INPUTS
Battery Supply Voltage Range
Fully Operational
Extended mode⁽⁷⁾
Battery Clamp Voltage⁽⁸⁾
V_PWR Operating Supply Current
Outputs commanded ON, HS[0 : 3] open, IN[0:3] > V_IH
V_PWR
6.0
–
4.0
–
V
20
28
V_PWR(CLAMP)
41
47
53
V
I_PWR(ON)
mA
–
6.5
20
V_PWR Supply Current
I_PWR(SBY)
Outputs commanded OFF, OFF Open-load Detection Disabled,
HS[0 : 3] shorted to the ground with V_DD= 5.5V
–
WAKE > V_IH or RST > V_IH and IN[0:3] < V_IL
mA
6.0
8.0
Sleep State Supply Current
I_PWR(SLEEP)
μA
V_PWR = 12V, RST = WAKE = IN[0:3] < V_IL, HS[0 : 3] shorted to the
ground
T_A = 25°C
T_A = 85°C
–
1.0
5.0
–
–
30
V_DD Supply Voltage
V_DD Supply Current at V_DD = 5.5V
No SPI Communication
8.0MHz SPI Communication⁽⁹⁾
V_DD(ON)
3.0
–
5.5
V
I_DD(ON)
mA
–
1.6
2.2
–
5.0
–
V_DD Sleep State Current at V_DD = 5.5V
Over-voltage Shutdown Threshold
Over-voltage Shutdown Hysteresis
Under-voltage Shutdown Threshold⁽¹⁰⁾
V_PWR and V_DD Power on Reset Threshold
V_DD Supply Failure Threshold ( for V_PWR > V_PWR(UV) )
Recovery Under-voltage Threshold
OUTPUTS HS0 TO HS3
I_DD(SLEEP)
–
–
5.0
μA
V_PWR(OV)
28
32
36
V
V_PWR(OVHYS)
0.2
0.8
1.5
V
V_PWR(UV)
3.3
3.9
4.3
V
V_SUPPLY(POR)
0.5
–
0.9
V_PWR(UV)
V_DD(FAIL)
2.2
2.5
2.8
V
V_{PWR(UV)_UP}
3.4
4.1
4.5
V
Output Drain-to-Source ON Resistance (I_HS = 2.0A, T_A = 25°C)
V_PWR = 4.0V
V_PWR = 6.0V
V_PWR = 10V
V_PWR = 13V
R_{DS(ON)_25}
–
–
–
–
mΩ
–
100
–
55
–
35
–
35
Notes
7. In extended mode, the functionality is guaranteed but not the electrical parameters. From 4.0V to 6.0V voltage range, the device is only
protected with the thermal shutdown detection.
8. Measured with the outputs open.
9. Typical value guaranteed per design.
10. Output will automatically recover with time limited autoretry to instructed state when V_PWR voltage is restored to normal as long as the
V_PWR degradation level did not go below the under-voltage power-ON reset threshold. This applies to all internal device logic that is
supplied by V_PWR and assumes that the external V_DD supply is within specification.
35XS3400
6
Analog Integrated Circuit Device Data
Freescale Semiconductor