PALCE29M16H-25 Datasheet, PDF (12/22 Pages) Advanced Micro Devices – 24-Pin EE CMOS Programmable Array Logic

AMD
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied . . . . . . . . . . . . . –55°C to +125°C
Supply Voltage with
Respect to Ground . . . . . . . . . . . . . –0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . –0.5 V to VCC + 0.5 V
DC Output or I/O
Pin Voltage . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current (TA = 0°C to +75°C) . . . . . 100 mA
Stresses above those listed under Absolute Maximum Rat-
ings may cause permanent device failure. Functionality at or
above these limits is not implied. Exposure to Absolute Maxi-
mum Ratings for extended periods may affect device reliabil-
ity. Programming conditions may differ.
OPERATING RANGES
Commercial (C) Devices
Ambient Temperature (TA)
Operating in Free Air . . . . . . . . . . . . . . . 0°C to 75°C
Supply Voltage (VCC)
with Respect to Ground . . . . . . . . . . 4.75 V to 5.25 V
Operating ranges define those limits between which the func-
tionality of the device is guaranteed.
DC CHARACTERISTICS over COMMERCIAL operating ranges unless otherwise
specified
Parameter
Symbol
VOH
Parameter Description
Output HIGH Voltage
VOL
Output LOW Voltage
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
IIH
Input HIGH Leakage Current
IIL
Input LOW Leakage Current
IOZH
Off-State Output Leakage
Current HIGH
IOZL
Off-State Output Leakage
Current LOW
ISC
Output Short-Circuit Current
ICC
Supply Current
Test Conditions
IOH = –2 mA
VIN = VIH or VIL
VCC = Min
IOL = 8 mA
VIN = VIH or VIL
IOL = 4 mA
VCC = Min
IOL = 20 µA
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 1)
Guaranteed Input Logical LOW
Voltage for all Inputs (Note 1)
VIN = 5.5 V, VCC = Max (Note 2)
VIN = 0 V, VCC = Max (Note 2)
VOUT = 5.5 V, VCC = Max
VIN = VIH or VIL (Note 2)
VOUT = 5.5 V, VCC = Max
VIN = VIH or VIL (Note 2)
VOUT = 0.5 V, VCC = Max (Note 3)
VIN = 0 V, Outputs Open (IOUT = 0 mA)
VCC = Max
Min Max Unit
2.4
V
0.5
0.33 V
0.1
2.0
V
0.8
V
10 µA
–10 µA
10 µA
–10 µA
–30 –130 mA
100 mA
Notes:
1. These are absolute values with respect to device ground all overshoots due to system and/or tester noise are included.
2. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).
3. Not more than one output should be shorted at a time and duration of the short-circuit should not exceed one second.
VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
2-338
PALCE29M16H-25 (Com’l)