SM59R16A5 Datasheet, PDF (38/89 Pages) SyncMOS Technologies,Inc – Two serial peripheral interfaces in full duplex mode

SM59R16A5/SM59R09A5/SM59R05A5
8-Bit Micro-controller
64KB/36KB/20KB with ISP Flash
& 2KB RAM embedded
Mnemonic: T2CON
7
6
5
T2PS[2:0]
4
3
T2R[1:0]
Address: C8h
2
1
0 Reset
-
T2I[1:0]
00H
T2PS[2:0]: Prescaler select bit:
T2PS = 000 – timer 2 is clocked with the oscillator frequency.
T2PS = 001 – timer 2 is clocked with 1/2 of the oscillator frequency.
T2PS = 010 – timer 2 is clocked with 1/4 of the oscillator frequency.
T2PS = 011 – timer 2 is clocked with 1/6 of the oscillator frequency.
T2PS = 100 – timer 2 is clocked with 1/8 of the oscillator frequency.
T2PS = 101 – timer 2 is clocked with 1/12 of the oscillator frequency.
T2PS = 110 – timer 2 is clocked with 1/24 of the oscillator frequency.
T2R[1:0]: Timer 2 reload mode selection
T2R[1:0] = 0X – Reload disabled
T2R[1:0] = 10 – Mode 0: Auto Reload
T2R[1:0] = 11 – Mode 1: T2EX Falling Edge Reload
T2I[1:0]: Timer 2 input selection
T2I[1:0] = 00 – Timer 2 stop
T2I[1:0] = 01 – Input frequency from prescaler(T2PS[2:0])
T2I[1:0] = 10 – Timer 2 is incremented by external signal at pin T2
T2I[1:0] = 11 – internal clock input is gated to the Timer 2
Mnemonic: CCCON
7
6
5
CCI3 CCI2 CCI1
4
CCI0
3
CCF3
2
CCF2
1
CCF1
Address: C9h
0 Reset
CCF0 00H
CCI3: Compare/Capture 3 interrupt control bit.
“1” is enable.
CCI2: Compare/Capture 2 interrupt control bit.
“1” is enable.
CCI1: Compare/Capture 1 interrupt control bit.
“1” is enable.
CCI0: Compare/Capture 0 interrupt control bit.
“1” is enable.
CCF3: Compare/Capture 3 flag set by hardware. This flag can be cleared by software.
CCF2: Compare/Capture 2 flag set by hardware. This flag can be cleared by software.
CCF1: Compare/Capture 1 flag set by hardware. This flag can be cleared by software.
CCF0: Compare/Capture 0 flag set by hardware. This flag can be cleared by software.
Compare/Capture interrupt share T2 interrupt vector.
Mnemonic: CCEN
7
6
5
4
--
COCAM1[2:0]
Address: C1h
3
2
1
0 Reset
--
COCAM0[2:0]
00H
COCAM1[2:0] 000: Compare/Capture disable
001: Compare enable but no output on Pin
010: Compare mode 0
011: Compare mode 1
100: Capture on rising edge at pin CC1
101: Capture on falling edge at pin CC1
110: Capture on both rising and falling edge at pin CC1
111: Capture on write operation into register CC1
COCAM0[2:0] 000: Compare/Capture disable
001: Compare enable but no output on Pin
010: Compare mode 0
011: Compare mode 1
Specifications subject to change without notice contact your sales representatives for the most recent information.
ISSFD-M047
38
Ver.H SM59R16A5 04/2015