M306V5ME-XXXSP Datasheet, PDF (247/263 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER

MITSUBISHI MICROCOMPUTERS
M306V5ME-XXXSP
M306V5EESP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
and ON-SCREEN DISPLAY CONTROLLER
5.3 Electrical Characteristics
Table 5.3.1 Electrical characteristics (referenced to VCC = 5 V, VSS = 0 V at Ta = 25 ^oC, f(XIN) = 10 MHz
unless otherwise specified)
Symbol
Parameter
Measuring condition
Standard
Min. Typ. Max.
Unit
VOH
HIGH output P00 to P07, P20 to P27,
IOH = –5 mA
voltage
P30 to P37, P40 to P43,
P50, P52, P53, P55, P62, P63, P67,
P72, P74, P76,
P82, P90, P93, P94, P100, P101, R,
G, B, OUT1, OUT2
VOH
HIGH output P00 to P07,P20 to P27, P30 to P37, IOH = –200 µA
voltage
P40 to P43, P50, P52, P53, P55
3.0
V
4.7
V
VOH
VOL
VOL
VOL
VOL
VT+-VT-
VT+-VT-
VT+-VT-
IIH
IIL
PPULLUP
Icc
HIGH output XOUT
HIGH POWER IOH = –1 mA
3.0
voltage
LOW POWER IOH = –0.5 mA
3.0
LOW output
voltage
P00 to P07, P20 to P27,
P30 to P37, P40 to P43,
P50, P52, P53, P55,
P62, P63, P74, P76,
P82, P90, P100, P101, R, G, B,
OUT1, OUT2
IOL = 5 mA
LOW output P67, P70 to P72, P93, P94
voltage
IOL = 6.0 mA
LOW output P00 to P07,P20 to P27, P30 to P37, IOL = 200 µA
voltage
P40 to P43, P50, P52, P53, P55
LOW output XOUT
voltage
HIGHPOWER
LOWPOWER
IOL = 1 mA
IOL = 0.5 mA
Hysteresis TB0IN, INT0, INT1, CLK0, CLK2,
0.2
SCL1, SCL2, SCL3,
SDA1, SDA2, SDA3,
HSYNC, VSYNC, HC0, HC1, RxD0,
RxD2
Hysteresis RESET
0.2
Hysteresis XIN
0.2
HIGH input
current
P00 to P07, P20 to P27,
P30 to P37, P40 to P43,
P50, P52, P53, P55, P62, P63, P67,
P70, P71, P72, P74, P76,
P82, P90, P93, P94, P100, P101
XIN, RESET, CNVss, OSC1
VI = 5 V
LOW input
current
Pull-up resistor
P00 to P07, P20 to P27,
P30 to P37, P40 to P43,
P50, P52, P53, P55, P62, P63, P67,
P70, P71, P72, P74, P76,
P82, P90, P93, P94, P100, P101
XIN, RESET, CNVss, OSC1
P00 to P07, P20 to P27,
P30 to P37, P40 to P43,
P50, P52, P53, P55, P62, P63, P67,
P72, P74, P76, P82, P90, P93, P94
VI = 0 V
VI = 0 V
30.0
Power supply current
f(XIN) = 10 MHz _{OSD ON, Data slicer ON}
Square wave,
no division
OSD OFF, Data slicer OFF
In single-chip
mode, the
f(XIN) = 10 MHz
Square wave,
OSD OFF, Data slicer OFF
output pins division by 8
are open and
other pins are
VS S
Ta=25 °C when
clock is stopped
V
2.0 V
0.6 V
0.45 V
2.0 _V
2.0
0.8 V
1.8 V
0.8 V
5.0 µA
–5.0 ^µA
50.0 167.0 kΩ
70
90
mA
30
50
10
mA
10
RBS
RfXIN
Ta = 70 °C when
clock is stopped
I²C-BUS • BUS switch connection resistor ^{Vcc = 4.5 V}
(between SCL1 and SCL2, SDA1 and SDA2)
Feedback resistor XIN
µA
200
130 Ω
1.0
MΩ
RfXCIN
Feedback resistor XCIN
6.0
MΩ
Rev. 1.0
246