COP840CJ Datasheet, PDF (8/36 Pages) National Semiconductor (TI) – 8-Bit Microcontrollers with Multi-Input Wake-Up and Brown Out Detector

DC Electrical Characteristics COP84x (Continued)
−40˚C ≤ T_A ≤ +85˚C unless otherwise specified
Parameter
Condition
Maximum Input Current
Min
Typ
Max
Units
±100
mA
without Latchup (Note 12)
RAM Retention Voltage, Vr
500 ns Rise and Fall Time (min)
2.0
V
Input Capacitance
7
pF
Load Capacitance on D2
1000
pF
Note 9: Rate of voltage change must be < 10V/ms.
Note 10: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 11: The HALT mode will stop CKI from oscillating in the RC and crystal configurations. HALT test conditions: L, and G0..G5 ports configured as outputs and
set high. The D port set to zero. All inputs tied to V_CC. The comparator and the Brown Out circuits are disabled.
Note 12: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than V_CC and the pins will have sink current
to V_CC when biased at voltages greater than V_CC (the pins do not have source current when biased at a voltage below V_CC). The effective resistance to V_CC is 750Ω
(typical). These two pins will not latch up. The voltage at the pins must be limited to < 14V.
Note 13: The Resistor values are for R/C only.
AC Electrical Characteristics COP84x
−40˚C ≤ T_A ≤ +85˚C unless otherwise specified.
Parameter
Condition
Instruction Cycle Time (t_C)
Crystal/Resonator
R/C Oscillator
V_CC Rise Time when Using Brown Out
Frequency at Brown Out Reset
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
4.5V < V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
CKI Frequency for Modulator Output
CKI Clock Duty Cycle (Note 14)
Rise Time (Note 14)
Fall Time (Note 14)
fr = Max
fr = 10 MHz ext. clock
fr = 10 MHz ext. clock
Inputs
t_Setup
t_Hold
Output Propagation Delay
t_PD1, t_PD0
SO, SK
All Others
Input Pulse Width
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
R_L = 2.2k, C_L = 100 pF
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer input low time
MICROWIRE Setup Time (t_µWS)
MICROWIRE Hold Time (t_µWH)
MICROWIRE Output
Propagation Delay (t_µPD)
Reset Pulse Width
Note 14: Parameter sampled but not 100% tested.
www.national.com
8
Min
Typ
Max
1
DC
2.5
DC
2
DC
5
DC
50
4
4
40
60
12
8
200
500
60
150
Units
µs
µs
µs
µs
µs
MHz
MHz
%
ns
ns
ns
ns
ns
ns
0.7
µs
1.75
µs
1
µs
5
µs
1
t_C
1
t_C
1
t_C
1
t_C
1
t_C
20
ns
56
ns
220
ns
1.0
µs