COP840CJ Datasheet, PDF (5/36 Pages) National Semiconductor (TI) – 8-Bit Microcontrollers with Multi-Input Wake-Up and Brown Out Detector

DC Electrical Characteristics COP94x (Continued)
0˚C ≤ T_A ≤ +70˚C unless otherwise specified
Parameter
Condition
Min
Typ
Max
Units
Allowable Sink/Source Current per
Pin
D Outputs
15
mA
L4–L7 (sink)
20
mA
All Others
Maximum Input Current
3
mA
±100
mA
without Latchup (Note 5)
RAM Retention Voltage, Vr
500 ns Rise and
2.0
V
Fall Time (min)
Input Capacitance
7
pF
Load Capacitance on D2
1000
pF
Note 2: Rate of voltage change must be < 10V/ms.
Note 3: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 4: The HALT mode will stop CKI from oscillating in the RC and crystal configurations. HALT test conditions: L, and G0..G5 ports configured as outputs and set
high. The D port set to zero. All inputs tied to V_CC. The comparator and the Brown Out circuits are disabled.
Note 5: Pins G6 and RESET are designed with a high voltage input network. These pins allow input voltages greater than V_CC and the pins will have sink current
to V_CC when biased at voltages greater than V_CC (the pins do not have source current when biased at a voltage below V_CC). The effective resistance to V_CC is 750Ω
(typical). These two pins will not latch up. The voltage at the pins must be limited to < 14V.
Note 6: The Resistor values are for R/C only.
AC Electrical Characteristics COP94x
0˚C ≤ T_A ≤ +70˚C unless otherwise specified
Parameter
Condition
Instruction Cycle Time (t_C)
Crystal/Resonator
R/C Oscillator
V_CC Rise Time when Using Brown Out
Frequency at Brown Out Reset
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
4.5V ≤ V_CC < 6.0V
2.5V ≤ V_CC < 4.5V
CKI Frequency for Modulator Output
CKI Clock Duty Cycle (Note 7)
fr = Max
Rise Time (Note 7)
fr = 10 MHz ext. clock
Fall Time (Note 7)
fr = 10 MHz ext. clock
Inputs
t_Setup
tHold
Output Propagation Delay
4.5V ≤ V_CC < 6.0
2.5V ≤ V_CC < 4.5
4.5V ≤ V_CC < 6.0
2.5V ≤ V_CC < 4.5
RL = 2.2k, CL = 100 pF
t_PD1, t_PD0
SO, SK
All Others
Input Pulse Width
4.5V ≤ V_CC < 6.0
2.5V ≤ V_CC < 4.5
4.5V ≤ V_CC < 6.0
2.5V ≤ V_CC < 4.5
Interrupt Input High Time
Interrupt Input Low Time
Timer Input High Time
Timer Input Low Time
5
Min
Typ
Max
1
DC
2.5
DC
2
DC
5
DC
50
4
4
40
60
12
8
200
500
60
150
Units
µs
µs
µs
µs
µs
MHz
MHz
%
ns
ns
ns
ns
ns
ns
0.7
µs
1.75
µs
1
µs
5
µs
1
t_C
1
t_C
1
t_C
1
t_C
1
t_C
www.national.com