PIC18F6390_07 Datasheet, PDF (360/414 Pages) Microchip Technology – 64/80-Pin Flash Microcontrollers with LCD Driver and nanoWatt Technology

PIC18F6390/6490/8390/8490
26.2
DC Characteristics:
Power-Down and Supply Current
PIC18F6390/6490/8390/8490 (Industrial)
PIC18LF6390/6490/8390/8490 (Industrial) (Continued)
PIC18LF6390/6490/8390/8490
(Industrial)
PIC18F6390/6490/8390/8490
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Device
Typ Max Units
Conditions
Supply Current (IDD)⁽²⁾
PIC18LF6390/6490/8390/8490 59 117 μA
-40°C
59 108 μA
+25°C
VDD = 2.0V
63 104 μA
+85°C
PIC18LF6390/6490/8390/8490 108 243 μA
108 225 μA
117 216 μA
-40°C
+25°C
+85°C
VDD = 3.0V
FOSC = 1 MHz
(PRI_IDLE mode,
EC oscillator)
All devices 270 432 μA
-40°C
216 405 μA
+25°C
VDD = 5.0V
270 387 μA
+85°C
PIC18LF6390/6490/8390/8490 234 428 μA
-40°C
230 405 μA
+25°C
VDD = 2.0V
243 387 μA
+85°C
PIC18LF6390/6490/8390/8490 378 810 μA
387 765 μA
405 729 μA
-40°C
+25°C
+85°C
VDD = 3.0V
FOSC = 4 MHz
(PRI_IDLE mode,
EC oscillator)
All devices .8 1.35 mA
-40°C
.8 1.26 mA
+25°C
VDD = 5.0V
.8 1.17 mA
+85°C
All devices 5.4 14.4 mA
-40°C
5.6 14.4 mA
5.9 14.4 mA
All devices 7.3 16.2 mA
8.2 16.2 mA
+25°C
+85°C
-40°C
+25°C
VDD = 4.2V
VDD = 5.0V
FOSC = 40 MHz
(PRI_IDLE mode,
EC oscillator)
7.5 16.2 mA
+85°C
Legend:
Note 1:
2:
3:
4:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS;
MCLR = VDD; WDT enabled/disabled as specified.
Low-power Timer1 oscillator selected.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be
less than the sum of both specifications.
DS39629C-page 358
© 2007 Microchip Technology Inc.