PIC18F6390_07 Datasheet, PDF (230/414 Pages) Microchip Technology – 64/80-Pin Flash Microcontrollers with LCD Driver and nanoWatt Technology

PIC18F6390/6490/8390/8490
17.3.2 AUSART SYNCHRONOUS
MASTER RECEPTION
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTA2<5>), or the Continuous Receive
Enable bit, CREN (RCSTA2<4>). Data is sampled on
the RX2 pin on the falling edge of the clock.
If enable bit, SREN, is set, only a single word is
received. If enable bit, CREN, is set, the reception is
continuous until CREN is cleared. If both bits are set,
then CREN takes precedence.
To set up a Synchronous Master Reception:
1. Initialize the SPBRG2 register for the appropriate
baud rate.
2. Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
3. Ensure bits, CREN and SREN, are clear.
4. If interrupts are desired, set enable bit, RC2IE.
5. If 9-bit reception is desired, set bit, RX9.
6. If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
7. Interrupt flag bit, RC2IF, will be set when recep-
tion is complete and an interrupt will be generated
if the enable bit, RC2IE, was set.
8. Read the RCSTA2 register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
9. Read the 8-bit received data by reading the
RCREG2 register.
10. If any error occurred, clear the error by clearing
bit, CREN.
11. If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
FIGURE 17-8:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RX2/DT2 pin
bit 0
bit 1
bit 2
bit 3
bit 4
bit 5
bit 6
bit 7
TX2/CK2 pin
Write to
SREN bit
SREN bit
CREN bit ‘0’
‘0’
RC2IF bit
(Interrupt)
Read
RCREG2
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
TABLE 17-7: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Reset
Values
on Page
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF
59
PIR3
—
LCDIF RC2IF TX2IF
—
—
—
—
61
PIE3
—
LCDIE RC2IE TX2IE
—
—
—
—
61
IPR3
—
LCDIP RC2IP TX2IP
—
—
—
—
61
RCSTA2 SPEN
RX9
SREN CREN ADDEN FERR OERR RX9D
63
RCREG2 AUSART2 Receive Register
63
TXSTA2 CSRC
TX9
TXEN SYNC
—
BRGH TRMT TX9D
63
SPBRG2 AUSART2 Baud Rate Generator Register
63
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.
DS39629C-page 228
© 2007 Microchip Technology Inc.