PIC16F627A Datasheet, PDF (11/168 Pages) Microchip Technology – FLASH-Based 8-Bit CMOS Microcontrollers

PIC16F627A/628A/648A
3.0 ARCHITECTURAL OVERVIEW
The high performance of the PIC16F627A/628A/648A
family can be attributed to a number of architectural
features commonly found in RISC microprocessors. To
begin with, the PIC16F627A/628A/648A uses a Har-
vard architecture, in which program and data are
accessed from separate memories using separate bus-
ses. This improves bandwidth over traditional von Neu-
mann architecture where program and data are fetched
from the same memory. Separating program and data
memory further allows instructions to be sized differ-
ently than 8-bit wide data word. Instruction opcodes are
14-bits wide making it possible to have all single word
instructions. A 14-bit wide program memory access
bus fetches a 14-bit instruction in a single cycle. A two-
stage pipeline overlaps fetch and execution of instruc-
tions. Consequently, all instructions (35) execute in a
single-cycle (200 ns @ 20 MHz) except for program
branches.
Table 3-1 lists device memory sizes (FLASH, Data and
EEPROM).
TABLE 3-1: DEVICE MEMORY LIST
Device
PIC16F627A
PIC16F628A
PIC16F648A
PIC16LF627A
PIC16LF628A
PIC16LF648A
FLASH
Program
1024 x 14
2048 x 14
4096 x 14
1024 x 14
2048 x 14
4096 x 14
Memory
RAM
Data
224 x 8
224 x 8
256 x 8
224 x 8
224 x 8
256 x 8
EEPROM
Data
128 x 8
128 x 8
256 x 8
128 x 8
128 x 8
256 x 8
The PIC16F627A/628A/648A can directly or indirectly
address its register files or data memory. All Special
Function Registers, including the program counter, are
mapped in the data memory. The PIC16F627A/628A/
648A have an orthogonal (symmetrical) instruction set
that makes it possible to carry out any operation, on
any register, using any Addressing mode. This sym-
metrical nature and lack of ‘special optimal situations’
make programming with the PIC16F627A/628A/648A
simple yet efficient. In addition, the learning curve is
reduced significantly.
The PIC16F627A/628A/648A devices contain an 8-bit
ALU and working register. The ALU is a general pur-
pose arithmetic unit. It performs arithmetic and Boolean
functions between data in the working register and any
register file.
The ALU is 8-bit wide and capable of addition,
subtraction, shift and logical operations. Unless
otherwise mentioned, arithmetic operations are two's
complement in nature. In two-operand instructions,
typically one operand is the working register
(W register). The other operand is a file register or an
immediate constant. In single operand instructions, the
operand is either the W register or a file register.
The W register is an 8-bit working register used for ALU
operations. It is not an addressable register.
Depending on the instruction executed, the ALU may
affect the values of the Carry (C), Digit Carry (DC), and
Zero (Z) bits in the STATUS register. The C and DC bits
operate as a Borrow and Digit Borrow out bit,
respectively, bit in subtraction. See the SUBLW and
SUBWF instructions for examples.
A simplified block diagram is shown in Figure 3-1, and
a description of the device pins in Table 3-2.
Two types of data memory are provided on the
PIC16F627A/628A/648A devices. Non-volatile
EEPROM data memory is provided for long term stor-
age of data such as calibration values, look up table
data, and any other data which may require periodic
updating in the field. These data are not lost when
power is removed. The other data memory provided is
regular RAM data memory. Regular RAM data memory
is provided for temporary storage of data during normal
operation. Data are lost when power is removed.
 2002 Microchip Technology Inc.
Preliminary
DS40044A-page 9