MAX1126 Datasheet, PDF (2/25 Pages) Maxim Integrated Products – Quad, 12-Bit, 40Msps, 1.8V ADC with Serial LVDS Outputs

Quad, 12-Bit, 40Msps, 1.8V ADC with
Serial LVDS Outputs
ABSOLUTE MAXIMUM RATINGS
AV_DD to GND.........................................................-0.3V to +2.0V
CV_DD to GND ........................................................-0.3V to +3.6V
OV_DD to GND ........................................................-0.3V to +2.0V
IN_P, IN_N to GND...................................-0.3V to (AV_DD + 0.3V)
CLK to GND .............................................-0.3V to (CV_DD + 0.3V)
OUT_P, OUT_N, FRAME_,
CLKOUT_ to GND................................-0.3V to (OV_DD + 0.3V)
DT, SLVS/LVDS to GND ...........................-0.3V to (AV_DD + 0.3V)
PLL0, PLL1, PLL2, PLL3 to GND .............-0.3V to (AV_DD + 0.3V)
PD0, PD1, PD2, PD3, PDALL to GND......-0.3V to (AV_DD + 0.3V)
T/B, LVDSTEST to GND ...........................-0.3V to (AV_DD + 0.3V)
REFIO, INTREF to GND............................-0.3V to (AV_DD + 0.3V)
I.C. to GND...............................................-0.3V to (AV_DD + 0.3V)
Continuous Power Dissipation (T_A = +70°C)
68-Pin QFN 10mm x 10mm x 0.9mm
(derated 41.7mW/°C above +70°C)........................3333.3mW
Operating Temperature Range ...........................-40°C to +85°C
Maximum Junction Temperature .....................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature Range (soldering, 10s)......................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(AV_DD = 1.8V, OV_DD = 1.8V, CV_DD = 1.8V, GND = 0, external V_REFIO = 1.24V, INTREF = AV_DD, C_REFIO to GND = 0.1µF,
f_CLK = 40MHz (50% duty cycle), DT = 0, T_A = T_MIN to T_MAX, unless otherwise noted. Typical values are at T_A = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
DC ACCURACY
Resolution
N
Integral Nonlinearity
INL
(Note 2)
Differential Nonlinearity
DNL (Note 2)
Offset Error
Fixed external reference (Note 2)
Gain Error
Fixed external reference (Note 2)
ANALOG INPUTS (IN_P, IN_N)
Input Differential Range
V_ID
Differential input
Common-Mode Voltage Range
V_CMO (Note 3)
Differential Input Impedance
R_IN
Switched capacitor load
Differential Input Capacitance
C_IN
CONVERSION RATE
Maximum Conversion Rate
Minimum Conversion Rate
f_SMAX
f_SMIN
Data Latency
DYNAMIC CHARACTERISTICS (differential inputs, 4096-point FFT)
Signal-to-Noise Ratio (Note 2)
Signal-to-Noise and Distortion
(First Four Harmonics) (Note 2)
Effective Number of Bits (Note 2)
SNR
SINAD
ENOB
f_IN = 5.3MHz at -0.5dBFS
f_IN = 19.3MHz at -0.5dBFS, T_A ≥ +25°C
f_IN = 5.3MHz at -0.5dBFS
f_IN = 19.3MHz at -0.5dBFS, T_A ≥ +25°C
f_IN = 5.3MHz at -0.5dBFS
f_IN = 19.3MHz at -0.5dBFS
MIN TYP MAX UNITS
12
-1.5
±0.4
±0.25
+0.9
±1
+2.5
Bits
LSB
LSB
% FS
% FS
1.4
0.75
2
12.5
V_P-P
V
kΩ
pF
40
16
6.5
MHz
MHz
Cycles
69.9
dB
66.7 69.2
69.8
dB
66.7 69.1
11.4
Bits
11.3
2 _______________________________________________________________________________________