801-2-31-A40 Datasheet, PDF(18/28 Page) Magnetrol International, Inc. – KotronTM II Series 801 RF Capacitance Transmitter For Level/Flow/Volume

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

801-2-31-A40 Datasheet, PDF (18/28 Pages) Magnetrol International, Inc. – KotronTM II Series 801 RF Capacitance Transmitter For Level/Flow/Volume

◁

UNIT CONFIGURATION cont.

SYSTEM CONFIG MENU cont

Flow and Level

Flow Element cont.

Rectangular/End Contractions (Rct/Cntr)

Rectangular

Cipolletti

Palmer Bowlus 4"

10"

12"

15"

18"

21"

24"

27"

30"

H-Flume 6"

12"

18"

24"

30"

36"

54"

Custom Table

With Flow Element displayed, press ENT to display the

selection. Use the UP or DOWN arrow to scroll through the

Flow Element selections. When the desired flow element is

displayed, press ENT.

If the flow element is changed, Password? will be displayed

and your chosen password must be entered at this time. The

unit will display the next menu item - Flow Units.

NOTE: If the Rectangular/End Contractions, Rectangular or

Cipoletti is selected, the unit will prompt the user for the width

of the flow element.

If the flow element for your application is not in the menu.

select the custom table to configure a 51 point strapping

table. Press ENT on display of Custom Table. Your pass-

word will be required, then Table Name will be displayed.

Press ENT and input the table name via 2nd key. Refer to

Page 16 for volume custom table configuration. Press ENT

and read Max. Table Span. Press ENT and key in maximum

span level. Press ENT once again and read Max Table

Value and press ENT. Key in desired Max. table value (usu-

ally equal to the 100% value) and press ENT. Table Units

will appear. Key in any appropriate units and press ENT.

Input 51 points in the strapping table and press ENT. Refer

to Page 16, Custom Table Entry for volume mode, for more

information about the Custom Table Entry.

SYSTEM CONFIG MENU cont

Flow Units

Cubic Feet/Sec

Cubic Feet/Min

Cubic Feet /Hr

Gallons/Min

Gallons/Hr

Million Gals/Day

Cubic Meters/Sec

Cubic Meters/Min

Cubic Meters/Hr

Liters/Min

Liters/Hour

MegaLiters/Day

With Flow Units displayed, press ENT to display the selec-

tions. Use the UP or DOWN arrow to scroll through the Flow

Units. When the desired flow unit is displayed, press ENT.

The unit will display the next menu item - Low Flow Cutoff.

Flow and Level

Low Flow Cutoff

Cut â

With Low Flow Cutoff displayed, press ENT to display

Cut.

Low Flow Cutoff is the low level cutoff value in the chosen

units of level. This will force a zero flow value when the level

is at or below this Low Cutoff Value. Enter the value and

press ENT. Password? will be displayed and your chosen

password must be entered at this time. The unit will display

the next menu item â Level Limit.

Press ENT to display the maximum level possible in the pre-

sent units of measurement. Press ENT to display the next

menu item â Probe Lo.

NOTES:

1. The Probe Lo and Probe Hi points are the most critical

entries in the calibration procedure. Be sure of the val-

ues before they are entered.

2. The media level must be moved to accomplish this pro-

cedure. The Probe Lo and Probe Hi points can be

entered in any order and can be easily changed in the

future when the process level is at a much higher or

lower point.

3. A minimum level change of two percent (2%) of flume

flow (or 5pF, whichever is greater) will yield a valid

calibration, however, a large change yields better

accuracy.

4. The unit will automatically "time out" and revert back to

the Default Display after four minutes if without a key-

stroke. Any information already entered will remain in

memory. Simply reenter the System Config. section and

enter any remaining data.

▷