V-SERIES Datasheet, PDF (32/45 Pages) Keysight Technologies – Infiniium V-Series Oscilloscopes

32 | Keysight | Infiniium V-Series Oscilloscopes - Data Sheet
Infiniium V-Series Performance Characteristics
Vertical
DSO/DSA/MSO models
Vertical - oscilloscope channels
Input channels
Analog bandwidth (—3 dB)
2 channel ¹
2 channel (typical)
4 channel ¹
4 channel (typical)
Rise time/fall time
10 to 90% ⁵
20 to 80% ⁶
Input impedance ²
Input sensitivity ³
Full scale hardware sensitivity
Input coupling
Vertical resolution ^{3, 4}
Channel-to-channel isolation
(any two channels with equal V/div
settings)
DC gain accuracy ^{1, 2, 3, 4}
Maximum input voltage
Offset range
V084A
V134A
V164A
V204A
DSO/DSA models - 4 analog
MSO models - 4 analog + 16 digital
8 GHz
8.4 GHz
8 GHz
8.4 GHz
13 GHz
13.6 GHz
13 GHz
13.6 GHz
16 GHz
16.8 GHz
16 GHz
16.8 GHz
20 GHz
21 GHz
16 GHz
16.8 GHz
55.0 ps
33.8 ps
27.5 ps
22.0 ps
38.9 ps
23.9 ps
19.4 ps
15.6 ps
50 Ω, ± 3%
1 mV/div to 1 V/div
60 mV to 8 V (oscilloscope only)
60 mV to 1.2 V (oscilloscope with N7010A voltage termination adapter)
DC
8 bits, ≥ 12 bits with high-resolution mode or averaging
Channel-to-channel: 1-3, 1-4, 2-3, and 2-4
DC to BW: 70 dB
Channel-to-channel: 1-2 and 3-4
DC to 4 GHz: 50 dB
4 to 12 GHz: 40 dB
12 GHz to BW: 35 dB
± 2% of full scale at full resolution channel scale (± 2.5% for ≤ 5 mV/div)
±5V
Vertical sensitivity
Available offset
Offset accuracy ¹
Dynamic range
DC voltage measurement accuracy
1 to 49 mV/div
± 0.4 V
50 to 79 mV/div
± 0.7 V
80 to 134 mV/div
± 1.2 V
135 to 239 mV/div
± 2.2 V
240 mV/div to 1 V/div
± 4.0 V
≤ 3.5 V: ± (2% of channel offset + 1% of full scale + 1 mV)
> 3.5 V: ± (2% of channel offset + 1% of full scale)
± 4 div from center screen
Dual cursor: ± [(DC gain accuracy) + (resolution)]
Single cursor: ± [(DC gain accuracy) + (offset accuracy) + (resolution/2)]
V254A
V334A
25 GHz
26.2 GHz
16 GHz
16.8 GHz
17.6 ps
12.4 ps
32 GHz
33 GHz
16 GHz
16.8 GHz
13.3 ps
9.4 ps
Available offset (oscilloscope with
N7010A voltage termination adapter)
Additional ± 4 V
Additional ± 4 V
Additional ± 4 V
Additional ± 4 V
Additional ± 4 V
1.  Denotes warranted specifications, all others are typical. Specifications are valid after 30-minute warm up period and ± 5% from oscilloscope firmware
calibration temperature.
2.  Input impedance is valid when V/div scaling is adjusted to show all waveform vertical values within scope display.
3.  Full scale is defined as eight vertical divisions. Magnification is used below 7.5 mV/div. Below 7.5 mV/div, full scale is defined as 60 mV/div. The major scale
settings are 1 mV/div, 2 mV/div, 5 mV/div, 10 mV/div, 20 mV/div, 50 mV/div, 100 mV/div, 200 mV/div, 500 mV/div and 1V/div.
4.  Vertical resolution for 8 bits = 0.4% of full scale, for 12 bits = 0.024% of full scale.
5.  Calculation based on Tr = 0.44/BW.
6.  Calculation based on Tr = 0.31/BW.