HMT41GA7MFR8A Datasheet, PDF(14/48 Page) Hynix Semiconductor – DDR3L SDRAM ECC SO-DIMMs Based on 4Gb M-die

English

English German Russian Spanish Italian Polish Chinese Japanese Korean French Portuguese	Language :

HMT41GA7MFR8A Datasheet, PDF (14/48 Pages) Hynix Semiconductor – DDR3L SDRAM ECC SO-DIMMs Based on 4Gb M-die

◁

AC and DC Input Levels for Single-Ended Signals

DDR3 SDRAM will support two Vih/Vil AC levels for DDR3-800 and DDR3-1066s specified in table below.

DDR3 SDRAM will also support corresponding tDS values (Table 43 on page 117 and Table 50 on page 142

in âDDR3L Device Operationâ) as well as derating tables Table 46 on page 135 in âDDR3L Device Opera-

tionâ depending on Vih/Vil AC levels.

Single Ended AC and DC Input Levels for DQ and DM

Symbol

Parameter

DDR3L-800/1066

Min

Max

DDR3L-1333/1600

Min

Max

Unit Notes

VIH.DQ(DC90) DC input logic high

VIL.DQ(DC90) DC input logic low

VIH.DQ(AC160) AC input logic high

VIL.DQ(AC160) AC input logic low

VIH.DQ(AC135) AC Input logic high

Vref + 0.09

VSS

Vref + 0.160

Note2

Vref + 0.135

VDD

Vref - 0.09

Note2

Vref - 0.160

Note2

Vref + 0.09

VSS

Vref + 0.135

VDD

Vref - 0.09

Note2

V 1, 2, 5

VIL.DQ(AC135) AC input logic low

Note2

Vref - 0.135

Note2

Vref - 0.135 V 1, 2, 5

VIH.DQ(AC130) AC Input logic high

V 1, 2, 5

VIL.DQ(AC130) AC input logic low

V 1, 2, 5

VRefDQ(DC)

Reference Voltage

for DQ, DM inputs

0.49 * VDD

0.51 * VDD

0.49 * VDD

0.51 * VDD V 3, 4

Notes:

1. Vref = VrefDQ (DC).

2. Refer to "Overshoot and Undershoot Specifications" on page 26.

3. The ac peak noise on VRef may not allow VRef to deviate from VRefDQ(DC) by more than +/-1% VDD (for

reference: approx. +/- 13.5 mV). 4. For reference: approx. VDD/2 +/- 13.5 mV

4. For reference: approx. VDD/2 +/- 13.5 mV

5. These levels apply for 1.35 volt (table "Single Ended AC and DC Input Levels for Command and

Address" on page 13) operation only. If the device is operated at 1.5V (table above), the respective levels

in JESD79-3 (VIH/L.DQ(DC100), VIH/L.DQ(AC175), VIH/L.DQ(AC150), VIH/L.DQ(AC135) etc.) apply. The

1.5V levels (VIH/L.DQ(DC100), VIH/L.DQ(AC175), VIH/L.DQ(AC150), VIH/L.DQ(AC135) etc.) do not apply

when the device is operated in the 1.35 voltage range.

Rev. 0.1 / Jul. 2012

▷