XRT83L30_06 Datasheet, PDF (2/78 Pages) Exar Corporation – SINGLE-CHANNEL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR

XRT83L30
SINGLE-CHANNEL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
FIGURE 2. BLOCK DIAGRAM OF THE XRT83L30 T1/E1/J1 LIU (HARDWARE MODE)
MCLKE1
MCLKT1
CLKSEL[2:0]
TXTEST[0:2]
INSBPV
TPOS / TDATA
TNEG / CODES
TCLK
QRPD
RCLK
RNEG / LCV
RPOS / RDATA
NLCD
RLOS
HW/HOST
GAUGE
JASEL1
JASEL0
RXTSEL
TXTSEL
TERSEL1
TERSEL0
RXRES1
RXRES0
MASTER CLOCK SYNTHESIZER
QRSS
PATTERN
GENERATOR
QRSS ENABLE
QRSS
DETECTOR
NETWORK
LOOP
DETECTOR
HDB3/
B8ZS
ENCODER
TX/RX JITTER
ATTENUATOR
TAOS
ENABLE
TIMING
CONTROL
DFM
DRIVE
MONITOR
TX FILTER
& PULSE
SHAPER
LINE
DRIVER
REMOTE
LOOPBACK
DIGITAL
LOOPBACK
LOOPBACK
ENABLE
HDB3/
B8ZS
DECODER
TX/RX JITTER
ATTENUATOR
TIMING &
DATA
RECOVERY
LBO[3:0]
PEAK
DETECTOR
& SLICER
LOCAL
ANALOG
LOOPBACK
RX
EQUALIZER
NLCD ENABLE
LOS
DETECTOR
AIS
DETECTOR
EQUALIZER
CONTROL
TEST
HARWARE CONTROL
MCLKOUT
DMO
TTIP
TRING
TXON
RTIP
RRING
LOOP1
LOOP0
AISD
ICT
JABW
TRATIO
SR/DR
EQC[4:0]
TCLKE
RCLKE
RXMUTE
ATAOS
RESET
FEATURES
• Fully integrated single-channel long-haul and short-haul transceiver for E1,T1 or J1 applications.
• Adaptive Receive Equalizer for cable attenuation of up to 45dB for T1 and 43dB for E1.
• Programmable Transmit Pulse Shaper for E1,T1 or J1 short-haul interfaces.
• Five fixed transmit pulse settings for T1 short-haul applications plus a fully programmable waveform
generator for transmit output pulse shaping.
• Programmable Transmit Line Build-Outs (LBO) for T1 long-haul application from 0dB to -22.5dB in three
7.5dB steps.
• Tri-State transmit output and receive input capability for redundancy applications
• Selectable receiver sensitivity from 0 to 36dB or 0 to 45dB cable loss for T1 @772kHz and 0 to 43dB for E1
@1024kHz.
• High receiver interference immunity
• Receive monitor mode handles 0 to 29dB resistive attenuation along with 0 to 6dB of cable attenuation for
both T1 and E1 modes.
• Supports 75Ω and 120Ω (E1), 100Ω (T1) and 110Ω (J1) applications.
• Internal and external impedance matching for 75Ω,100Ω, 110Ω and 120Ω.
• Transmit return loss meets or exceeds ETSI 300 166 standard
• On-chip digital clock recovery circuit for high input jitter tolerance
• Crystal-less digital jitter attenuator with 32-bit or 64-bit FIFO Selectable either in transmit or receive path
• On-chip frequency multiplier generates T1 or E1 Master clocks from variety of external clock sources
• On-chip transmit short-circuit protection and limiting, and driver fail monitor output (DMO)
2