XRT83L30_06 Datasheet, PDF (1/78 Pages) Exar Corporation – SINGLE-CHANNEL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR

XRT83L30
SINGLE-CHANNEL T1/E1/J1 LH/SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
JUNE 2006
REV. 1.0.1
GENERAL DESCRIPTION
The XRT83L30 is a fully integrated single-channel
long-haul and short-haul line interface unit for
T1(1.544Mbps) 100Ω, E1(2.048Mbps) 75Ω or 120Ω
and J1 110Ω applications.
In long-haul applications the XRT83L30 accepts
signals that have passed through cables from 0 feet
to over 6000 feet in length and have been attenuated
by 0 to 45dB at 772kHz in T1 mode or 0 to 43dB at
1024kHz in E1 mode. In T1 applications, the
XRT83L30 can generate five transmit pulse shapes
to meet the short-haul Digital Cross-Connect (DSX-1)
template requirements as well as for Channel Service
Units (CSU) Line Build Out (LBO) filters of 0dB,
-7.5dB, -15dB and -22.5dB as required by FCC rules.
It also provides programmable transmit pulse
generator that can be used for arbitrary output pulse
shaping allowing performance improvement over a
wide variety of conditions.
The XRT83L30 provides both Serial Host
microprocessor interface and Hardware Mode for
programming and control. Both B8ZS and HDB3
encoding and decoding functions are included and
can be disabled as required. On-chip crystal-less jitter
attenuator with a 32 or 64 bit FIFO can be placed
either in the receive or the transmit path with loop
bandwidths of less than 3Hz. The XRT83L30
provides a variety of loop-back and diagnostic
features as well as transmit driver short circuit
detection and receive loss of signal monitoring. It
supports internal impedance matching for 75Ω, 100Ω,
110Ω and 120Ω for both transmitter and receiver. For
the receiver this is accomplished by internal resistors
or through the combination of one single fixed value
external resistor and programmable internal resistors.
In the absence of the power supply, the transmit
output and receive input are tri-stated allowing for
redundancy applications. The chip includes an
integrated programmable clock multiplier that can
synthesize T1 or E1 master clocks from a variety of
external clock sources.
APPLICATIONS
• T1 Digital Cross-Connects (DSX-1)
• ISDN Primary Rate Interface
• CSU/DSU E1/T1/J1 Interface
• T1/E1/J1 LAN/WAN Routers
• Public switching Systems and PBX Interfaces
• T1/E1/J1 Multiplexer and Channel Banks
FEATURES
(See Page 2)
FIGURE 1. BLOCK DIAGRAM OF THE XRT83L30 T1/E1/J1 LIU (HOST MODE)
MCLKE1
MCLKT1
TXTEST[0:2]
INSBPV
TPOS / TDATA
TNEG / CODES
TCLK
QRPD
RCLK
RNEG / LCV
RPOS / RDATA
NLCD
RLOS
HW/HOST
CS
INT
MASTER CLOCK SYNTHESIZER
QRSS
PATTERN
GENERATOR
QRSS ENABLE
QRSS
DETECTOR
NETWORK
LOOP
DETECTOR
HDB3/
B8ZS
ENCODER
TAOS
ENABLE
TX/RX JITTER
ATTENUATOR
TIMING
CONTROL
TX FILTER
& PULSE
SHAPER
DRIVE
MONITOR
LINE
DRIVER
REMOTE
LOOPBACK
DIGITAL
LOOPBACK
LOOPBACK
ENABLE
HDB3/
B8ZS
DECODER
TX/RX JITTER
ATTENUATOR
TIMING &
DATA
RECOVERY
LBO[3:0]
PEAK
DETECTOR
& SLICER
LOCAL
ANALOG
LOOPBACK
RX
EQUALIZER
NLCD ENABLE
LOS
DETECTOR
AIS
DETECTOR
EQUALIZER
CONTROL
Serial Interface
TEST
MCLKOUT
DMO
TTIP
TRING
TXON
RTIP
RRING
AISD
ICT
SDO
SCLK
SDI
RESET
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • [phone] • FAX [phone] • www.exar.com