SMH4046 Datasheet, PDF (9/51 Pages) List of Unclassifed Manufacturers – Hot-Swap, Active DC Output Control (ADOCTM) Power Manager with I2C lnterface

SMH4046
Preliminary Information
ABSOLUTE MAXIMUM RATINGS
Temperature Under Bias ...................... -55°C to 125°C
Storage Temperature............................ -65°C to 150°C
Terminal Voltage with Respect to GND:
VCC3/5 Supply Voltage .....................-0.3V to 6.0V
VCC12 Supply Voltage ....................-0.3V to 15.0V
Open Drain Outputs...…………...… GND to 15.0V
All Others ..............................................V_DD + 0.7V
Output Short Circuit Current ............................... 100mA
Reflow Solder Temperature (30 secs)................. 240°C
Lead Solder Temperature (10 secs) …………….300°C
Junction Temperature.......................…….....…...150°C
ESD Rating per JEDEC…………..………..……..2000V
Latch-Up testing per JEDEC………..……....…±100mA
Note - The device is not guaranteed to function outside its operating
rating. Stresses listed under Absolute Maximum Ratings may cause
permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions
outside those listed in the operational sections of the specification is
not implied. Exposure to any absolute maximum rating for extended
periods may affect device performance and reliability. Devices are
ESD sensitive. Handling precautions are recommended.
RECOMMENDED OPERATING CONDITIONS
Temperature Range (Industrial)...........–40°C to +85°C
(Commercial) ..............0°C to +70°C
VCC3V Supply Voltage................................. 2.7V to 5V
VCC5V Supply Voltage................................. 2.7V to 6V
VCC12V Supply Voltage… ………..….....6.0V to 14.0V
VIN .......................................................... GND to VCC5
VOUT ...................................................... GND to 15.0V
Package Thermal Resistance (θ_JA)
48 Lead TQFP……………………………...…80^oC/W
Moisture Classification Level 1 (MSL 1) per J-STD- 020
RELIABILITY CHARACTERISTICS
Data Retention……………………………..….100 Years
Endurance……………………………….100,000 Cycles
DC OPERATING CHARACTERISTICS
(Over recommended operating conditions, unless otherwise noted. All voltages are relative to GND)
Symbol
Parameter
Notes
Min
Typ
Max Unit
VCC3 Supply Voltage Monitor
Not a supply input
2.7
3.3
5.0
V
VCC5 Supply Voltage
VCC5 must be higher then
any other input except
2.7
5.0
6.0
V
VCC12 and CARD12V
VCC12 Supply Voltage Monitor
Not a supply input
6
12
14
V
VMx
Positive sense voltage for VMA,
VMB and VMC
-0.3
VCC5V
I_DD
I_TRIM
V_TRIM
V_IH
V_IL
V_OL
Power Supply Current
All TRIM pins floating
3
5
mA
TRIMA, TRIMB, TRIMC current
Margin Control and ADOC Range
Input High Voltage
Input Low Voltage
TRIMx pin sourcing current
1.5
TRIMx pin sinking current
I_TRIM ±1.5mA, Depends on
Trim range of DC-DC
Converter
VCC5V = 2.7V
VCC5V = 5.0V
VCC5V = 2.7V
VCC5V = 5.0V
1.5
GND
0.9xVCC5V
0.7xVCC5V
mA
mA
VCC5V V
VCC5V V
VCC5V V
0.1xVCC5V V
0.3xVCC5V V
Programmable Open Drain Outputs I_SINK = 1mA
0.2
V
Summit Microelectronics, Inc
2082 1.7 08/23/04
9