|
CS42L55 Datasheet, PDF (36/73 Pages) Cirrus Logic – Ultra Low Power, Stereo CODEC w/Class H Headphone Amp | |||
|
◁ |
CS42L55
4.11.1 Recommended Power-Down Sequence
1. To minimize pops on the headphone or line amplifier, each respective analog volume control must
first be muted and set to maximum attenuation.
Register Controls: HPxMUTE, LINExMUTE, HPxVOL[6:0], LINExVOL[6:0]
2. Set the PDN bit to â1âb.
3. Bring RESET low.
Power Down Sequence Register Location
Step 1a ................................ âHeadphone Volume Controlâ on page 57, âLine Volume Controlâ on page 58
Step 1b ................................ âHeadphone Channel x Muteâ on page 57, âLine Channel x Muteâ on page 58
Step 2 .................................. âPower Downâ on page 42
4.12
Recommended PGA to HP or Line Power-Up Sequence (Analog Passthrough)
1. Hold RESET low until the power supplies are stable; no specific power supply sequencing is required.
RESET should be held low for a minimum of 1 ms after power supplies are stable.
2. Apply MCLK at the appropriate frequency.
3. Bring RESET high.
4. Wait a minimum of 500 ns before writing to the control port.
5. The default state of the master power down bit, PDN, is â1âb. Load the following register settings while
keeping the PDN bit set to â1âb.
6. Load the required register settings detailed in 4.13 âRequired Initialization Settingsâ on page 37.
7. Configure the headphone and line power down controls for ON, OFF, or HPDETECT operation.
Register Controls: PDN_HPx[1:0], PDN_LINx[1:0]
8. Configure the HP and/or Line amplifiers to receive the analog output from the PGA.
Register Controls: LINExMUX, HPxMUX
9. Power down the DSP engine.
Register Controls: PDN_DSP
10. To minimize pops on the headphone or line amplifier, each respective analog volume control must first
be muted and set to maximum attenuation.
Register Controls: HPxMUTE, LINExMUTE, HPxVOL[6:0], LINExVOL[6:0]
11. After muting the headphone and/or line amplifiers, set the PDN bit to â0âb.
12. Wait 75 ms for the headphone or line amplifier to power up.
13. Un-mute and ramp the volume for the headphone or line amplifiers to the desired level.
14. Bring RESET low if the analog or digital supplies drop below the recommended operating condition to
prevent power glitch related issues.
Power Up Sequence
Register Location
Step 5, 11 ............................
Step 7 ..................................
Steps 8 ................................
Step 9 ..................................
Step 10a,13a .......................
Step 10b,13b .......................
âPower Downâ on page 42
âPower Control 2 (Address 03h)â on page 43
âADC, Line, HP MUX (Address 08h)â on page 46
âPower Down DSPâ on page 50
âHeadphone Channel x Muteâ on page 57, âLine Channel x Muteâ on page 58
âHeadphone Volume Controlâ on page 57, âLine Volume Controlâ on page 58
4.12.1
Recommended Power-Down Sequence
1. To minimize pops on the headphone and/or line amplifier, each respective analog volume control
must first be muted and set to maximum attenuation.
Register Controls: HPxMUTE, LINExMUTE, HPxVOL[6:0], LINExVOL[6:0]
2. During power down, the CODEC attempts to power down on a zero cross transition of the analog
36
DS773F1
|
▷ |