AM186EM Datasheet, PDF (51/98 Pages) List of Unclassifed Manufacturers – MICROCONTROLLER BLOCK DIAGRAM

PRELIMINARY
ABSOLUTE MAXIMUM RATINGS
Storage temperature
Am186EM/Am188EM ..................... –65°C to +125°C
Am186EMLV/Am188EMLV............. –65°C to +125°C
Voltage on any pin with respect to ground
Am186/188EM ........................... –0.5 V to V_cc +0.5 V
Am186/188EMLV ....................... –0.5 V to V_cc +0.5 V
Note: Stresses above those listed under Absolute
Maximum Ratings may cause permanent device failure.
Functionality at or above these limits is not implied. Ex-
posure to absolute maximum ratings for extended peri-
ods may affect device reliability.
OPERATING RANGES
Operating Ranges define those limits between which
the functionality of the device is guaranteed.
Am186EM/Am188EM Microcontrollers
Commercial (T_C) .................................0°C to +100°C
Industrial* (T_A)...................................–40°C to +85°C
V_CC up to 33 MHz ..................................... 5 V ± 10%
V_CC greater than 33 MHz............................ 5 V ± 5%
Am186EMLV/Am188EMLV Microcontrollers
Commercial (T_A) ................................... 0°C to +70°C
V_CC up to 25 MHz ................................. 3.3 V ± 0.3 V
Where: T_C = case temperature
T_A = ambient temperature
*Industrial versions of Am186EM and Am188EM microcontrol-
lers are available in 20 and 25 MHz operating frequencies
only.
DC CHARACTERISTICS OVER COMMERCIAL OPERATING RANGE
Symbol
Parameter Description
V_IL Input Low Voltage (Except X1)
V_IL1 Clock Input Low Voltage (X1)
V_IH Input High Voltage (Except RES and X1)
V_IH1 Input High Voltage (RES)
V_IH2 Clock Input High Voltage (X1)
Output Low Voltage
Am186EM and Am188EM
V_OL
Am186EMLV and Am188EMLV
Output High Voltage^(a)
Am186EM and Am188EM
V_OH
Am186EMLV and Am188EMLV
Power Supply Current @ 0°C
Am186EM and Am188EM
I_CC
Am186EMLV and Am188EMLV
Test Conditions
I_OL= 2.5 mA (S2–S0)
I_OL= 2.0 mA (others)
I_OL= 1.5 mA (S2–S0)
I_OL= 1.0 mA (others)
I_OH= –2.4 mA @ 2.4 V
I_OH= –200 µA @ V_CC –0.5
I_OH= –200 µA @ V_CC –0.5
V_CC = 5.5 V ^(b)
V_CC = 3.6 V ^(b)
V_OL
I_LI
I_LO
V_CLO
V_CHO
Output Low Voltage
Input Leakage Current @ 0.5 MHz
Output Leakage Current @ 0.5 MHz
Clock Output Low
Clock Output High
I_OL = 2.5 mA (S2–S0)
I_OL = 2.0 mA (others)
0.45 V ≤ V_IN ≤ V_CC
0.45 V ≤ V_OUT ≤ V_CC(d)
I_CLO = 4.0 mA
I_CHO = –500 µA
Preliminary
Min
Max
– 0.5
0.8
– 0.5
0.8
2.0
2.4
V_CC – 0.8
V_CC + 0.5
V_CC + 0.5
V_CC + 0.5
0.45
Unit
V
V
V
V
V
V
0.45
V
2.4
V_CC –0.5
V_CC –0.5
V_CC – 0.5
V_CC +0.5
V_CC
V_CC
5.9
2.75
0.45
±10
±10
0.45
V
V
V
mA/
MHz
mA/
MHz
V
µA
µA
V
V
Notes:
a The LCS/ONCE0, MCS3–MCS0, UCS/ONCE1, and RD pins have weak internal pullup resistors. Loading the LCS/ONCE0 and
UCS/ONCE1 pins in excess of I_OH= –200 µA during reset can cause the device to go into ONCE mode.
b Current is measured with the device in RESET with X1 and X2 driven, and all other non-power pins open but held High or Low.
c Power supply current for the Am186EMLV and Am188EMLV microcontrollers, which are available in 20 and 25 MHz
operating frequencies only.
d Testing is performed with the pins floating, either during HOLD or by invoking the ONCE mode.
Am186/188EM and Am186/188EMLV Microcontrollers
51