TMDS261B Datasheet, PDF (8/48 Pages) Texas Instruments – TWO-PORT HDMI SWITCH

TMDS261B
SLLS987A – SEPTEMBER 2009 – REVISED JULY 2011
www.ti.com
Table 2. Control-Pin Lookup Table⁽¹⁾
SIGNAL
LP
S[2:1]
GPIO
mode
I2C_SEL
VSadj
LEVEL
H
L
S2 S1
HH
HL
L
L
LH
L
H
4.02 kΩ
STATE
Normal mode
Low-power
mode
DESCRIPTION
Normal operational mode for device. If LP is left floating, then a weak internal pullup to VCC
pulls it to VCC.
Device is forced into a low-power state, causing the inputs and outputs to go to a
high-impedance state. All other inputs are ignored.
Port 1
Port 1 is selected as the active port; all other ports are low.
Port 2
Port 2 is selected as the active port; all other ports are low.
Disallowed Disallowed (Indeterminate state; all terminations are disconnected.)
HPD[1:2] follow
HPD_SINK
Standby mode: HPD[1:2] follow HPD_sink.
I²C
Device is configured by I²C logic.
GPIO
Device is configured by GPIO. If the I2C_SEL pin is left floating, then a weak internal pullup to
VCC pulls the I2C_SEL pin high.
Compliant
voltage
Driver output voltage swing precision control to aid with system compliance. The VSadj
resistor value can be selected to be 4.02 kΩ ±10% based on the system requirement to pass
HDMI compliance.
(1) (H) Logic high; (L) Logic low
PART NUMBER
TMDS261BPAGR
TMDS261BPAG
ORDERING INFORMATION⁽¹⁾
PART MARKING
TMDS261B
TMDS261B
PACKAGE
64-pin TQFP reel (large)
64-pin TQFP tray
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)⁽¹⁾
Supply voltage range⁽²⁾ VCC
TMDS I/O
Voltage range
HPD and DDC I/O
Electrostatic discharge
Control and status I/O
Human body model⁽³⁾ on SCL[1:2], SDA[1:2], HPD[1:2], D[0:2]+_[1:2],
D[0:2]–_[1:2], CLK+_[1:2], CLK–_[1:2] pins
Human body model⁽³⁾ on all other pins
Charged-device model⁽⁴⁾
Machine model⁽⁵⁾
IEC 61000-4-2⁽⁶⁾, contact discharge
IEC 61000-4-2⁽⁶⁾, air discharge
Continuous power dissipation
VALUE
–0.3 to 3.6
–0.3 to 4
–0.3 to 5.5
–0.3 to 5.5
UNIT
V
V
±10,000
±9,000
±1500
V
±200
±8,000
±15,000
See Dissipation Ratings table
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values, except differential voltages, are with respect to network ground terminal.
(3) Tested in accordance with JEDEC Standard 22, Test Method A114-B
(4) Tested in accordance with JEDEC Standard 22, Test Method C101-A
(5) Tested in accordance with JEDEC Standard 22, Test Method A115-A
(6) Tested in accordance with IEC EN 61000-4-2
8
Copyright © 2009–2011, Texas Instruments Incorporated