DS80PCI810 Datasheet, PDF (7/60 Pages) Texas Instruments – Low-Power 8 Gbps 8-Channel Linear Repeater

www.ti.com
DS80PCI810
SNLS493A – OCTOBER 2014 – REVISED JANUARY 2015
6 Specifications
6.1 Absolute Maximum Ratings⁽¹⁾
over operating free-air temperature range (unless otherwise noted)
Supply Voltage (VDD to GND, 2.5 V Mode)
Supply Voltage (VIN to GND, 3.3 V Mode)
LVCMOS Input/Output Voltage
CML Input Voltage
CML Input Current
Storage temperature, T_stg
T_solder
Lead Temperature Range Soldering (4 sec.)⁽²⁾
MIN
MAX
UNIT
-0.5
+2.75
V
-0.5
+4.0
V
-0.5
+4.0
V
-0.5
VDD + 0.5
V
-30
+30
mA
-40
125
°C
260
°C
(1) “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other
conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions
indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Absolute Maximum
Numbers are ensured for a junction temperature range of -40°C to +125°C. Models are validated to Maximum Operating Voltages only.
(2) For soldering specifications: See application note SNOA549.
6.2 ESD Ratings
V_(ESD) Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001⁽¹⁾
Charged-device model (CDM), per JEDEC specification JESD22-
C101 ⁽²⁾
VALUE
±4000
±1000
UNIT
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions. Pins listed as ±4000 V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions. Pins listed as ±1000 V may actually have higher performance.
6.3 Handling Ratings
V_(ESD)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all
pins ⁽¹⁾
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins⁽²⁾
MIN
-4000
-1000
MAX
4000
1000
(1) JEDEC document JEP155 states that 4000-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 1000-V CDM allows safe manufacturing with a standard ESD control process.
UNIT
V
6.4 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
Supply Voltage (2.5 V mode)⁽¹⁾
Supply Voltage (3.3 V mode)⁽¹⁾
MIN
2.375
3.0
Ambient Temperature
-40
SMBus (SDA, SCL)
Supply Noise up to 50 MHz⁽²⁾
(1) DC plus AC power should not exceed these limits.
(2) Allowed supply noise (mVp-p sine wave) under typical conditions.
NOM
2.5
3.3
100
MAX
2.625
3.6
+85
3.6
UNIT
V
V
°C
V
mVp-p
Copyright © 2014–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7