CC2640R2F Datasheet, PDF (18/64 Pages) Texas Instruments – SimpleLink Bluetooth low energy Wireless MCU

CC2640R2F
SWRS204 – DECEMBER 2016
www.ti.com
5.7 125-kbps Coded (Bluetooth 5) – TX
Measured on the TI CC2650EM-5XD reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Output power, highest setting
Differential mode, delivered to a single-ended 50-Ω load
through a balun
5
dBm
Output power, highest setting
Measured on CC2650EM-4XS, delivered to a single-ended
50-Ω load
2
dBm
Output power, lowest setting Delivered to a single-ended 50-Ω load through a balun
–21
dBm
f < 1 GHz, outside restricted bands
–43
dBm
Spurious emission conducted ^{f < 1 GHz, restricted bands ETSI}
measurement ⁽¹⁾
f < 1 GHz, restricted bands FCC
–65
dBm
–76
dBm
f > 1 GHz, including harmonics
–46
dBm
(1) Suitable for systems targeting compliance with worldwide radio-frequency regulations ETSI EN 300 328 and EN 300 440 Class 2
(Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan).
5.8 500-kbps Coded (Bluetooth 5) – RX
Measured on the TI CC2650EM-5XD reference design with T_c = 25°C, V_DDS = 3.0 V, f_RF = 2440 MHz, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
Receiver sensitivity
Differential mode. Measured at the CC2650EM-5XD
SMA connector, BER = 10^–3
–101
dBm
Receiver saturation
Differential mode. Measured at the CC2650EM-5XD
SMA connector, BER = 10^–3
>5
dBm
Frequency error tolerance
Difference between the incoming carrier frequency
and the internally generated carrier frequency
–240
240 kHz
Data rate error tolerance
Difference between incoming data rate and the
internally generated data rate (37-byte packets)
–500
500 ppm
Data rate error tolerance
Difference between incoming data rate and the
internally generated data rate (255-byte packets)
–310
330 ppm
Co-channel rejection ⁽¹⁾
Wanted signal at –72 dBm, modulated interferer in
channel, BER = 10^–3
–5
dB
Selectivity, ±1 MHz ⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
±1 MHz, BER = 10^–3
9 / 5 ⁽²⁾
dB
Selectivity, ±2 MHz ⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
±2 MHz, Image frequency is at –2 MHz, BER = 10^–3
41 / 31⁽²⁾
dB
Selectivity, ±3 MHz ⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
±3 MHz, BER = 10^–3
44 / 41⁽²⁾
dB
Selectivity, ±4 MHz ⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
±4 MHz, BER = 10^–3
44 / 44⁽²⁾
dB
Selectivity, ±6 MHz ⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
±6 MHz, BER = 10^–3
44 / 44⁽²⁾
dB
Alternate channel rejection,
±7 MHz⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
≥ ±7 MHz, BER = 10^–3
44 / 44⁽²⁾
dB
Selectivity, image frequency⁽¹⁾
Wanted signal at –72 dBm, modulated interferer at
image frequency, BER = 10^–3
31
dB
Selectivity, image frequency
±1 MHz⁽¹⁾
Note that Image frequency + 1 MHz is the Co-
channel –1 MHz. Wanted signal at –72 dBm,
modulated interferer at ±1 MHz from image
frequency, BER = 10^–3
5 / 41⁽²⁾
dB
Blocker rejection, ±8 MHz and Wanted signal at –72 dBm, modulated interferer at
above ⁽¹⁾
±8 MHz and above, BER = 10^–3
Out-of-band blocking ⁽³⁾
30 MHz to 2000 MHz
44
dB
–35
dBm
Out-of-band blocking
2003 MHz to 2399 MHz
–19
dBm
Out-of-band blocking
2484 MHz to 2997 MHz
–19
dBm
(1) Numbers given as I/C dB.
(2) X / Y, where X is +N MHz and Y is –N MHz.
(3) Excluding one exception at F_wanted / 2, per Bluetooth Specification.
18
Specifications
Submit Documentation Feedback
Product Folder Links: CC2640R2F
Copyright © 2016, Texas Instruments Incorporated