OMAP5912 Datasheet, PDF (34/254 Pages) Texas Instruments – Applications Processor

Introduction
ZZG
BALL
NO.
SIGNAL
Table 2−2. ZZG Package Terminal Assignments (Continued)
ZZG
BALL
NO.
SIGNAL
ZZG
BALL
NO.
SIGNAL
ZZG
BALL
NO.
SIGNAL
UART3.RX(0)/
CAM.HS(0)/
CAM.VS(0)/
PWL(1)/
ETM.PSTAT[1](1)/
ETM.PSTAT[2](1)/
L8
FLASH.A[21]
L14
UART2.RX(3)/
L15
UART2.CTS(2)/
L18
MPUIO14(2)/
TIMER.PWM1(4)/
MMC2.DAT0/
MMC2.DAT1(3)
GPIO49(7)
GPIO38(7)
CAM.D[0](0)/
ETM.D[0](1)/
L19
MPUIO12(2)/
L21
MMC2.DAT3(3)
DV_DD8
M2
CV_DD
FLASH.CS1(0)/
M3
FLASH.CS1L(1)
FLASH.CS2(0)/
M4
FLASH.BAA(1)/
M7
FLASH.CS2L(2)
GPIO62(0)/
FLASH.CS0(1)
GPIO7(0)/
LOW_STATE^§(0)/
MMC.DAT2(1)/
UART3.TX(1)/
M15
TCK(3)/
M18
MCSI1.CLK(4)/
PWT(2)/
UART2.TX(4)
ETM.SYNC[1](5)/
TIMER.PWM0(5)/
RTDX.D[2](7)
GPIO50(7)
FLASH.BE[1](0)/
M8 FLASH.CS2UWE(1)/ M14
GPIO60(7)
CAM.RSTZ(0)/
ETM.PSTAT[0](1)/
M19
UART2.RTS(2)/
M20
MMC2.CLK(3)/
LOW_STATE^§(6)/
GPIO37(7)
GPIO2(0)/
ETM.PSTAT[4](5)/
RTDX.D[0] (7)
GPIO15(0)/
KB.R[7](1)/
TIMER.PWM2(2)
FLASH.CLK(0)/
N1
V_SS
N2
FLASH.D[1]
N3
FLASH.CS2UOE(1)
N4
FLASH.D[0]
Z_STATE^†(0)/
UWIRE.CS0(1)/
MPUIO2(0)/
N7
FLASH.D[2]
N8
FLASH.CS3(0)/
GPIO3(7)
N14
MCBSP3.CLKX(2)/
UART3.TX(4)/
EXT_DMA_REQ0(1)/
N15
UWIRE.CS1(2)/
SPIF.CS0(6)/
SPIF.CS1(6)
GPIO45(7)
GPIO12(0)/
N18
MCBSP3.FSX(1)/
N19
TIMER.EXTCLK(3)
GPIO13(0)/
KB.R[5](1)/
LCD.BLUE0(2)/
Z_STATE^†(3)
GPIO11(0)/
HDQ(1)/
N20
ETM.PSTAT[5](5)/
N21
RTDX.D[3](7)
GPIO14(0)/
KB.R[6](1)/
LCD.RED0(2)/
Z_STATE^†(3)
FLASH.CS2U(0)/
P2
FLASH.D[3]
P3
GPIO5(1)
P4
FLASH.D[4]
P7
FLASH.D[5]
USB.DP(0)/
MCBSP2.DR(0)/
I2C.SDA(4)
MCBSP2.DX(1)/
MMC.CMD/
P8
FLASH.D[11]
P9
UART1.RX(5)/
P10
MCBSP2.DXZ(2)/
P11
GPIO55(7)
USB.PUEN(7)
GPIO22(7)
† _{Z_STATE = high-impedance}
‡ _{“NC” denotes “No Connect”.}
§ _{LOW_STATE = 0}
¶ _{Signal must be tied low.}
NOTES: 1. Shading denotes signals with multiplexed functions.
2. The number within parenthesis at the end of a signal name denotes the Pin Mux setting (see the MUX CTRL SETTING column
in Table 2−3 and Table 2−4).
34 SPRS231D
December 2003 − Revised March 2005