AM1806 Datasheet, PDF (1/241 Pages) Texas Instruments – AM1806 ARM Microprocessor

AM1806
www.ti.com
AM1806 ARM Microprocessor
Check for Samples: AM1806
SPRS658 – FEBRUARY 2010
1 AM1806 ARM Microprocessor
1.1 Features
12
• 375/456-MHz ARM926EJ-S™ RISC MPU
• Enhanced Direct-Memory-Access Controller 3
(EDMA3):
– 2 Channel Controllers
– 3 Transfer Controllers
– 64 Independent DMA Channels
– 16 Quick DMA Channels
– Programmable Transfer Burst Size
• 1.8V or 3.3V LVCMOS IOs (except for USB and
DDR2 interfaces)
• Two External Memory Interfaces:
– EMIFA
• NOR (8-/16-Bit-Wide Data)
• NAND (8-/16-Bit-Wide Data)
• 16-Bit SDRAM With 128 MB Address
Space
– DDR2/Mobile DDR Memory Controller
• 16-Bit DDR2 SDRAM With 512 MB
Address Space or
• 16-Bit mDDR SDRAM With 256 MB
Address Space
• Three Configurable 16550 type UART Modules:
– With Modem Control Signals
– 16-byte FIFO
– 16x or 13x Oversampling Option
• Two Serial Peripheral Interfaces (SPI) Each
With Multiple Chip-Selects
• Two Multimedia Card (MMC)/Secure Digital (SD)
Card Interface with Secure Data I/O (SDIO)
Interfaces
• Two Master/Slave Inter-Integrated Circuit (I²C
Bus™)
• One Host-Port Interface (HPI) With 16-Bit-Wide
Muxed Address/Data Bus For High Bandwidth
• Programmable Real-Time Unit Subsystem
(PRUSS)
– Two Independent Programmable Realtime
Unit (PRU) Cores
• 32-Bit Load/Store RISC architecture
• 4K Byte instruction RAM per core
• 512 Bytes data RAM per core
• PRU Subsystem (PRUSS) can be disabled
via software to save power
• Register 30 of each PRU is exported from
the subsystem in addition to the normal
R31 output of the PRU cores.
– Standard power management mechanism
• Clock gating
• Entire subsystem under a single PSC
clock gating domain
– Dedicated interrupt controller
– Dedicated switched central resource
• USB 2.0 OTG Port With Integrated PHY (USB0)
– USB 2.0 High-/Full-Speed Client
– USB 2.0 High-/Full-/Low-Speed Host
– End Point 0 (Control)
– End Points 1,2,3,4 (Control, Bulk, Interrupt or
ISOC) Rx and Tx
• One Multichannel Audio Serial Port:
– Transmit/Receive Clocks
– Two Clock Zones and 16 Serial Data Pins
– Supports TDM, I2S, and Similar Formats
– DIT-Capable
– FIFO buffers for Transmit and Receive
• Two Multichannel Buffered Serial Ports:
– Transmit/Receive Clocks
– Two Clock Zones and 16 Serial Data Pins
– Supports TDM, I2S, and Similar Formats
– AC97 Audio Codec Interface
– Telecom Interfaces (ST-Bus, H100)
– 128-channel TDM
– FIFO buffers for Transmit and Receive
• Video Port Interface (VPIF):
– Two 8-bit SD (BT.656), Single 16-bit or Single
Raw (8-/10-/12-bit) Video Capture Channels
– Two 8-bit SD (BT.656), Single 16-bit Video
Display Channels
• Universal Parallel Port (uPP):
– High-Speed Parallel Interface to FPGAs and
Data Converters
– Data Width on Each of Two Channels is 8- to
16-bit Inclusive
– Single Data Rate or Dual Data Rate Transfers
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ARM926EJ-S is a trademark of ARM Limited.
2
ADVANCE INFORMATION concerns new products in the sampling
or preproduction phase of development. Characteristic data and other
specifications are subject to change without notice.
Copyright © 2010, Texas Instruments Incorporated