K4T56043QF Datasheet, PDF (13/27 Pages) Samsung semiconductor – 256Mb F-die DDR2 SDRAM

256Mb F-die DDR2 SDRAM
IDD Specification Parameters and Test Conditions
(IDD values are for full operating range of Voltage and Temperature, Notes 1 - 5)
DDR2 SDRAM
Symbol
IDD0
IDD1
IDD2P
IDD2Q
IDD2N
IDD3P
IDD3N
IDD4W
IDD4R
IDD5B
IDD6
IDD7
Proposed Conditions
Operating one bank active-precharge current;
tCK ₌ tCK(IDD), tRC ₌ tRC(IDD), tRAS ₌ tRASmin(IDD); _{CKE is HIGH, CS\ is HIGH between valid}
commands; Address bus inputs are SWITCHING; Data bus inputs are SWITCHING
Operating one bank active-read-precharge current;
IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; ^tCK = ^{tCK(IDD), tRC} = ^tRC (IDD), ^tRAS = ^tRAS-
min(IDD), ^tRCD = ^tRCD(IDD); CKE is HIGH, CS\ is HIGH between valid commands; Address busin-
puts are SWITCHING; Data pattern is same as IDD4W
Precharge power-down current;
All banks idle; tCK = ^tCK(IDD); CKE is LOW; Other control and address bus inputs are STABLE;
Data bus inputs are FLOATING
Precharge quiet standby current;
All banks idle; ^tCK = ^tCK(IDD); CKE is HIGH, CS\ is HIGH; Other control and address bus inputs are
STABLE; Data bus inputs are FLOATING
Precharge standby current;
All banks idle; ^tCK = ^tCK(IDD); CKE is HIGH, CS\ is HIGH; Other control and address bus inputs are
SWITCHING; Data bus inputs are SWITCHING
Active power-down current;
All banks open; ^tCK = ^tCK(IDD); CKE is LOW; Other control and
address bus inputs are STABLE; Data bus inputs are FLOATING
Fast PDN Exit MRS(12) =
0mA
Slow PDN Exit MRS(12) =
1mA
Active standby current;
All banks open; ^tCK = ^{tCK(IDD), tRAS} = ^{tRASmax(IDD), tRP} = ^tRP(IDD); CKE is HIGH, CS\ is HIGH
between valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs
are SWITCHING
Operating burst write current;
All banks open, Continuous burst writes; BL = 4, CL = CL(IDD), AL = 0; ^tCK = ^{tCK(IDD), tRAS} =
tRASmax(IDD), tRP ₌ tRP(IDD); _{CKE is HIGH, CS\ is HIGH between valid commands; Address bus}
inputs are SWITCHING; Data bus inputs are SWITCHING
Operating burst read current;
All banks open, Continuous burst reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = 0; ^tCK =
tCK(IDD), tRAS ₌ tRASmax(IDD), tRP ₌ tRP(IDD); _{CKE is HIGH, CS\ is HIGH between valid com-}
mands; Address bus inputs are SWITCHING; Data pattern is same as IDD4W
Burst auto refresh current;
tCK ₌ tCK(IDD); _{Refresh command at every} tRFC(IDD) _{interval; CKE is HIGH, CS\ is HIGH between}
valid commands; Other control and address bus inputs are SWITCHING; Data bus inputs are
SWITCHING
Self refresh current;
CK and CK\ at 0V; CKE ≤ 0.2V; Other control and address bus
inputs are FLOATING; Data bus inputs are FLOATING
Normal
Low Power
Operating bank interleave read current;
All bank interleaving reads, IOUT = 0mA; BL = 4, CL = CL(IDD), AL = ^{tRCD(IDD)-1*tCK(IDD); tCK} =
tCK(IDD), tRC ₌ tRC(IDD), tRRD ₌ tRRD(IDD), tRCD _{= 1*tCK(IDD); CKE is HIGH, CS\ is HIGH}
between valid commands; Address bus inputs are STABLE during DESELECTs; Data pattern is
same as IDD4R; Refer to the following page for detailed timing conditions
Units
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
Notes
Page 13 of 27
Rev. 1.5 Feb. 2005